Scheppach 5901222901 Traducción Del Manual De Instrucción Original página 32

• The moveable stop rails (16a) must be locked so
that the distance between the stop rails (16a) and
the saw blade (6) is at least 8 mm.
• Before making the cut, check that the stop rails
(16a) and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen the handle (11) if it is tightened. Pull the in-
dexed position lever (35) upwards with the pointer
finger. Adjust the rotary table (14) to the desired an-
gle using the handle (11).
• The pointer (12) on the rotary table must match the
desired angle on the scale (13) on the fixed saw
table (15).
• Re-tighten the handle (11) to secure the rotary table
(14).
• Cut as described under section 9.4.
9.6 Mitre cut 0°- 45° and turntable 0°
(fig. 1/2/11)
The crosscut, drag and mitre saw can be used to
make mitre cuts of 0° - 45° in relation to the work face.
Attention!
For bevel cuts (inclined saw head), the moveable stop
rail (16a) must be fixed in the outer position. (Left
side).
• Open the set screw (16b) for the moveable stop rail
(16a) and push the moveable stop rail (16a) out-
wards.
• The moveable stop rails (16a) must be locked so
that the distance between the stop rails (16a) and
the saw blade (6) is at least 8 mm.
• The moveable stop rail (28) must be fixed in the in-
ner position. (Right side).
• Before making a cut, check that the stop rail (16a) and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22). Use the handle (1) to an-
gle the machine head (4) to the left, until the pointer
(19) indicates the desired angle measurement on
the scale (18).
• Re-tighten the set screw (22).
• Cut as described in section 10.4.
9.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/2/4/12)
The crosscut, drag and mitre saw can be used to
make mitre cuts to the left of 0°- 45° in relation to the
work face and, at the same time, 0° - 45° to the left or
0° - 45° to the right in relation to the stop rail (double
mitre cut).
Attention!
For bevel cuts (inclined saw head), the moveable stop
rail (16a) must be fixed in the outer position. (Left
side).
32 | GB
 www.scheppach.com /  [email protected] /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Open the set screw (16b) for the moveable stop rail
(16a) and push the moveable stop rail (16a) out-
wards.
• The moveable stop rails (16a) must be locked so
that the distance between the stop rails (16a) and
the saw blade (6) is at least 8 mm.
• Before making a cut, check that the stop rails (16a)
and the saw blade (6) cannot collide.
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the han-
dle (11).
• Using the handle (11), set the rotary table (14) to
the desired angle (refer also to point 10.5 in this re-
gard).
• Re-tighten the handle (11) to secure the rotary table
(14).
• Undo the set screw (22).
• Use the handle (1) to tilt the machine head (4) to the
left until it coincides with the required angle value (in
this connection see also section 10.6).
• Re-tighten the set screw (22).
• Cut as described under section 9.4.
10. Maintenance
m Warning! Prior to any adjustment, maintenance
or service work disconnect the mains power plug!
10.1 General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of the
tool, oil the rotary parts once monthly. Do not oil the
motor.
When cleaning the plastic do not use corrosive prod-
ucts.
10.2 Cleaning the moving saw blade guard safety
device (5)
Always check the saw blade guard for debris before
using the machine.
Remove old sawdust and splinters using a brush or
similar tool.
10.3 Replacing the table insert
Danger!
With a damaged table insert (10) there is a risk of
small parts getting stuck between table insert and saw
blade, blocking the saw blade. Immediately replace
damaged table inserts!
1. Remove screws at table insert. If required, turn
rotary table and incline saw head to be able to
reach the screws.
2. Remove table insert.
3. Install new table insert.
4. Tighten the screws at table insert.