Idiomas disponibles
Idiomas disponibles
ENGlIsh
Wheel Mounting Accessories and
Attachments
It is important to choose the correct guards, backing pads
and flanges to use with grinder accessories. Refer to the
Accessories Chart for more information on choosing the
correct wheel mounting accessories.
Attachments
Attachments designed specifically for this grinder can be
purchased through D
WALT dealers and D
e
Service centers.
9" Type 27 guard
9" Type 28 guard
7" Type 27 guard
5"–6" Type 11 flaring cup guard
with flange
4" Type 11 flaring cup guard
with flange
Type 11 flaring cup wheel
backing flange
Type 1 flange set
7" Type 1 guard
Grinding backing flange
Clamp nut
Wheel wrench
Soft mount spindle protector
WARNING: Accessories must be rated for at least
the speed recom mended on the tool warning label.
Wheels and other accessories running over their
rated accessory speed may fly apart and cause injury.
Threaded accessories must have a 5/8"–11 hub. Every
unthreaded accessory must have a 7/8" (22.2 mm)
arbor hole. If it does not, it may have been designed
for a circular saw. Refer to the Accessories Chart for
more information. Accessory ratings must always be
above tool speed as shown on tool nameplate.
Mounting Guard
Mounting and Removing Guard
(Fig. E, F)
WARNING: Guards must be used with all
grinding wheels, cutting wheels, sanding flap
discs, wire brushes, and wire wheels. Guard
modification that results in reduced coverage
of the accessory could result in severe personal
injury. The tool may be used without a guard only
when sanding with conventional sanding discs. A
Type 27 guard (intended for use with depressed center
grinding wheels [Type 27 and Type 29], sanding flap
discs, wire wheels and wire cup brushes) is included
with the tool. Grinding and cutting with wheels
other than Type 27 and 29 require different accessory
38
1. Open the guard latch
Fig. E
WALT Factory
e
D284939
13
D284938
D284937
D284936
D284934
2. Push the guard down until the guard lugs engage and
N197992
3. With the guard latch open, rotate the guard
D284932
D284931
4. Close the guard latch to secure the guard on the gear
54339-00
N454941
635261-00
445928-01
5. To remove the guard, follow the procedure above in
NoTE: The guard is pre-adjusted to the diameter of the gear
case hub at the factory. If, after a period of time, the guard
becomes loose, tighten the adjusting screw
latch in the closed position with guard installed on the tool.
guards not included with tool. A Type 1 guard is for
use with the Type 1 wheel and is available at extra cost
from your local dealer or authorized service center.
Mounting instructions for accessory guards are shown
below and are also included in the accessory package.
13
the guard with the slots on the gear case
align the lugs on the guard with the slots on the gear
case cover.
14
15
can rotate freely into the groove on the gear case hub.
desired working position. The guard body should be
positioned between the spindle and the operator to
provide maximum operator protection.
case. You should not be able to rotate the guard by hand
when the latch is closed. Do not operate the grinder
with a loose guard or with the guard latch in open
position.
reverse order.
Fig. F
CAUTION: Do not tighten the adjusting screw with
the guard latch in the open position. Undetectable
damage to the guard or the mounting hub may result.
CAUTION: If the guard cannot be tightened by the
adjusting clamp, do not use the tool. To reduce the risk
of personal injury, take the tool and guard to a service
center to repair or replace the guard.
, and align the lugs
14
on
15
. This will
4
into the
16
16
with guard
4
