Idiomas disponibles
Idiomas disponibles
Use suitable substructures to ensure the load-
13.
bearing capacity and stability of the unit, particu-
larly in the case of thin worktops.
Take the appliance weight, including additional
‒
load, into consideration.
Use heat-resistant and moisture-resistant rein-
‒
forcement material.
Making the cut-out for the control knob
Create the holes for the control knob in accord-
1.
ance with the enclosed instructions.
If the panel is more than 23 mm thick, cut out the
2.
rear of the front panel for the retaining plate.
Note the clearances between the control knobs.
3.
→ Fig.
16
After making the cut-outs, remove any shavings.
4.
Seal the cut surfaces so that they are heat-resist-
5.
ant and waterproof.
Installing the control knob
Follow the installation instructions provided for the
1.
control knobs.
If required, and depending on the distance
2.
between the control knobs, break off the retaining
plate at the perforation.
→ Fig.
17
Hold the retaining plate in place against the rear
3.
of the control panel.
When fitting an individual control knob, use 2
4.
screws to hold the retaining plate in place and
prevent it from rotating.
In the case of stone worktops, stick the retain-
‒
ing plate using heat-resistant, two-component
adhesive.
→ Fig.
18
Remove the protective film from the rear of the il-
5.
luminated ring.
→ Fig.
19
Install the control knob in the correct sequence.
6.
→ Fig.
20
Push the control knob into the hole.
7.
Always position the side marking on the control
‒
knob on the left.
Ensure that the retaining lug on the retaining plate
8.
is located on the upper side and the control knob
is in the zero setting.
→ Fig.
21
On the rear of the control knob, tighten the retain-
9.
ing nut using the installation tool provided.
→ Fig.
22
Align the control knob precisely in the zero setting.
10.
Connecting the control knob to the
connection cables
Connect all of the control knobs to the enclosed
1.
connection cables.
→ Fig.
23
The two connectors on the control knob are
identical.
Ensure that the plugs snap into place in the con-
2.
nectors.
Connect the longer connection cable to any con-
3.
trol knob.
After installation, check that all of the plug connec-
4.
tions are seated correctly.
To secure all connection cables after installation,
5.
bend the mounting brackets on the retaining
plates.
→ Fig.
23
Installing the appliance
Ensure that the connection cable for the control
1.
knob engages in the socket on the underside of
the appliance.
→ Fig.
24
Keeping the appliance level, insert it into the unit
2.
cut-out.
→ Fig.
, → Fig.
25
26
Using both hands, push the appliance into the unit
3.
cut-out from above.
Ensure that the appliance is firmly positioned in
4.
the unit cut-out and does not move.
If necessary, if the width of the cut-out is at the up-
5.
per tolerance limit, secure a bar at the sides of the
cut-out in each case.
Connect the appliance to the power supply.
6.
Connect the appliance to the gas connection.
7.
Checking the functionality
Turn the control knob to 1.
1.
If the appliance is turned off, air may be present in
the gas line.
Turn the control knob to 0 and then back to 1.
2.
Repeat the process until the appliance ignites.
‒
Sealing the joints
For flush installation, seal the joints with silicone.
Requirements
You must carry out a function test before sealing
¡
any joints.
Before applying the sealant, check that the entire
¡
appliance fits precisely and that it is lying flat.
Seal all around the gap using suitable, heat-resist-
1.
ant silicone, e.g. Ottoseal® S70.
→ Fig.
27
Using unsuitable silicone adhesive on natural
stone work surfaces may cause permanent discol-
ouration.
Use the smoothing agent recommended by the
2.
manufacturer to smooth the joint.
Observe the usage instructions for the silicone ad-
3.
hesive.
Leave the silicone adhesive to dry for at least 24
4.
hours.
The drying time depends on the ambient temper-
ature.
Do not operate the appliance until the silicone has
5.
dried completely.
Fitting burner parts
Fit the burner parts and position them correctly.
▶
→ Fig.
28
Fitting the pan supports
Fit the pan supports and position them correctly.
▶
→ Fig.
29
Removing the appliance
ATTENTION!
Tools may damage the appliance.
Do not prise out the appliance from above.
▶
Disconnect the appliance from the power supply.
1.
Close the main gas tap.
2.
Push out the appliance from below.
3.
Technical specifications
You can find an overview of the total connected
loads for various types of gas and product variants
here.
15
