Idiomas disponibles
Idiomas disponibles
ENGlIsh
NoTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate a problem.).
LED Worklight (Fig. A)
CAUTION: Do not stare into worklight. Serious eye
injury could result.
There is a worklight
6
located on the foot of the drill near
the bit storage slot
7
. The worklight will be activated when
the trigger switch is squeezed.
NoTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
On Board Bit Storage (Fig. A)
A bit storage slot
is built-in to the foot of the drill.
7
Usage (Fig. A)
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous
condition. Inspect accessory prior to use to ensure that
it con tains no cracks.
CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
Excessive torque may cause breakage and possible
personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press variable speed trigger switch
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the
fastening torque is affected by many factors including
the following:
-
Voltage: Low voltage, due to a nearly discharged
battery, will reduce fastening torque.
-
accessory size: Failure to use the correct accessory
size will cause a reduction in fastening torque.
-
Bolt size: Larger bolt diameters generally
require higher fastening torque. Fastening torque
will also vary according to length, grade, and
torque coefficient.
Bolt: Ensure that all threads are free of rust and
-
other debris to allow proper fastening torque.
-
Material: The type of material and surface finish of
the material will affect fastening torque.
Fastening time: Longer fasten ing time results in
-
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.
MAINTENANCE
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning. Your charger does not require
any maintenance apart from regular cleaning.
WARNING! To reduce the risk of serious personal
injury, turn off the tool and disconnect it from
30
to start operation.
1
the power source before making adjustments or
removing / installing devices or accessories. An
accidental start could cause injuries.
IMPORTANT! To ensure product Safety and
Reliability, repairs, maintenance and adjustment
(other than those listed in this manual) should be
performed by authorized service centers or other
qualified organizations, always using identical
replacement parts. Unit contains no user service able
parts inside.
CLEANING
WARNING! Blow dirt and dust from all ventilation
ducts with dry air, at least once a week. To reduce
the risk of injury, always use ansi z87.1 Approved eye
protection when performing this task.
WARNING! Never use solvents or other abrasive
chemicals to clean non-metallic parts of the tool. These
chemicals can weaken the plastic materials used in these
parts. Use a cloth dampened only with water and neutral
soap. Never allow liquid to penetrate inside the tool or
immerse any of the parts in a liquid.
ACCESSORIES
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
WARNING! The use of any accessory not recommended
for use with this tool could be hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further
use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
BATTERIES
BLACK+DECKER batteries can be recharged many
times. At the end of their useful life, discard
batteries with due care for our environment:
•
Run the battery down completely, then remove it from
the tool.
•
NiCd, NiMH and Li-Ion batteries are recyclable. Take
them to any authorized repair agent or a local recycling
station.
