Idiomas disponibles
Idiomas disponibles
Safety of others
This appliance is not intended for use by persons
u
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
NOTE: Operating temperature of this tool is 7 to +40˚ C. Using
the tool outside of this temperature range will decrease the life
of the tool.
Do not store tool, battery and charger in locations where the
temperature may exceed 40 °C.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
● Injuries caused by touching any rotating/moving parts.
● Injuries caused when changing any parts, blades or
accessories.
● Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
● Impairment of hearing.
● Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration and noise
The declared vibration and noise emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method provided
by EN62841 and may be used for comparing one tool with
another.
The declared vibration and noise emission value may also be
used in a preliminary assessment of exposure.
WARNING! The vibration and noise emission value during
actual use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration
and noise level may increase above the level stated.
When assessing vibration and noise exposure to determine
safety measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
(Original instructions)
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
WARNING! To reduce the risk of injury, the user
must read the instruction manual.
Wear ear protectors with rotary hammer drills.
Exposure to noise can cause hearing loss
Wear safety glasses or goggles
Additional safety instructions for batteries and
chargers
Batteries
● Never attempt to open for any reason.
● Do not expose the battery to water.
● Do not expose the battery to heat.
● Do not store in locations where the temperature may
exceed 40 °C.
● Charge only at ambient temperatures between 10 °C and
40 °C.
● Charge only using the charger provided with the
appliance/tool.
● When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
● Do not damage/deform the battery pack either by puncture
or impact, as this may create a risk of injury and fire.
● Do not charge damaged batteries.
● Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
● In case of skin or eye contact, follow the instructions
@
below.
WARNING! The battery fluid may cause personal
injury or damage to property. In case of skin contact,
immediately rinse with water. If redness, pain or
irritation occurs seek medical attention. In case of
eye contact, rinse immediately with clean water and
seek medical attention.
Chargers
Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
@
the rating plate.
WARNING! Never attempt to replace the charger unit
with a regular mains plug.
● Use your charger only to charge the battery in the tool with
which it was supplied. Other batteries could burst, causing
personal injury and damage.
ENGLISH
7
