Safety Of Others; Residual Risks - Stanley SDS Plus Manual De Instrucciones

making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbol:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
f Wear ear protectors. Exposure to noise can cause
hearing loss.
f Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock
f Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
f Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it
unstable and may lead to loss of control.
f Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
f The intended use is described in this instruction
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recommended in this instruction manual
may present a risk of personal injury and/or damage to
property.

SAFETY OF OTHERS

f This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
f Children should be supervised to ensure that they do
not play with the appliance.

RESIDUAL RISKS

Additional residual risks may arise when using the
tool which may not be included in the enclosed safety
warnings. These risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
Construction
risks can not be avoided. These include:
Earthing
f Injuries caused by touching any rotating/moving
Terminal
parts.
Safety Alert
Symbol
f Injuries caused when changing any parts, blades
Revolutions
or accessories.
or Recipro-
f Injuries caused by prolonged use of a tool. When
cation per
minute
using any tool for prolonged periods ensure you
take regular breaks.
ENGLISH • 13
ADDITIONAL POWER TOOL
SAFETY WARNINGS