Idiomas disponibles
Idiomas disponibles
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (7a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack from the
tool
WARNING! Make certain the lock-off button is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack (No batteries for
SFMCH900B, one battery for SFMCH900M12, two
batteries for SFMCH900M22) (Fig. C)
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
Depress the battery release button (7b) as shown in figure
u
D and pull battery pack out of tool.
Fitting the side handle (fig. E)
Turn the grip counterclockwise until you can slide the side
u
handle (6) onto the front of the tool as shown.
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
u
Fitting and setting the depth stop (fig. E)
Depress the button (6b).
u
Insert the depth stop (4) into the mounting hole (6a) as
u
shown.
Set the depth stop (4) to the desired position. The
u
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
Release the button (6b).
u
Fitting an accessory (fig. F)
Clean and grease the shank (9) of the accessory.
u
Pull back the sleeve (5a) and insert the shank into the tool
u
holder (5).
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked. The
u
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
(Original instructions)
To remove the accessory, pull back the sleeve (5a) and
u
pull out the accessory.
WARNING! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
WARNING! Do not apply chisels when the tool is in the drilling
mode.
Selecting the operating mode (fig. G)
The tool can be used in three operating modes.
To operate the operating mode selector (3), push the
u
unlock button.
Rotate the selector towards the required position, as
indicated by the symbols.
Forward/reverse action (fig. H)
Move the selecter (2) to indicate the direction you require.
u
Switching on and off (fig. I)
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch.
u
Always hold the tool as shown in figure J.
Drilling
For drilling in steel, wood and plastics (only possible with
u
adapter, not supplied), and for screwdriving set the
operating mode selector (3) to the
Hammer drilling
For hammer drilling in masonry and concrete, set the
u
operating mode selector (3) to the
hammering, the tool should not bounce and run smoothly.
If necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
u
and chipping, set the operating mode selector (3) to the
position.
When changing from hammer drilling to chiselling, turn the
u
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the
spindle lock.
Accessories
The performance of your tool depends on the accessory used.
STANLEY FATMAX accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
WARNING! Since accessories, other than those offered by
STANLEY FATMAX, have not been tested with this product,
use of such accessories with this tool could be hazardous.
ENGLISH
position.
position. When
9
