Idiomas disponibles
Idiomas disponibles
Control Pro 350 M
Attention! The vibration emission value can differ from the specified value when the electric tool is actually in use, depending on
how the electric tool is being used. It is necessary to specify safety measures to protect the operating personnel. These measures are
based on an estimated shutdown during the actual conditions of use (all parts of the operating cycle are taken into consideration
here, for example periods when the electric tool is switched off, and, when it is switched on but running without any load).
Environmental protection
The device and all accessories and packaging have to be re-used in an environmentally friendly manner. Do
not dispose of the appliance with household waste. Support environmental protection by taking the appliance
to a local collection point or obtain information from a specialist retailer.
Leftover paint and solvents may not be emptied into drains, the sewage system or disposed of as household rubbish. It has
to be disposed of separately as special waste. Please pay special attention to the instructions on the product packaging.
Important Note regarding Product Liability!
Due to an EC ordinance in effect since 01.01.1990, the manufacturer is liable for his product only if all parts originate from or were
approved by the manufacturer and the devices are assembled and operated correctly. The use of other accessories and spare parts
can partially or completely invalidate the liability.
Correction of Malfunctions
Problem
Cause
•
The sprayer does
The sprayer is not plugged in.
•
not start.
The sprayer was turned off while still under
pressure.
•
No voltage is coming from the wall plug.
•
The extension cord is damaged or has too low
a capacity.
•
Device overheated
•
There is a problem with the motor.
•
The spray device
The unit will not prime properly or has lost
runs but does not
prime.
•
suck up any paint
The paint bucket is empty or the suction tube
when the selector
is not totally immersed in the paint.
•
switch is set to the
The suction tube is clogged.
•
PRIME position.
The inlet filter is clogged.
•
The suction tube is loose at the inlet valve.
•
The inlet valve or outlet valve is stuck.
•
The inlet valve is worn or damaged.
•
The PRIME/SPRAY valve is plugged
•
The sprayer draws
The spray nozzle is worn.
•
up paint but the
The inlet filter is clogged.
•
pressure drops
The spray nozzle is blocked (if fitted)
•
when the gun is
The paint is too viscous or contaminated.
•
triggered.
The inlet valve is worn or damaged.
•
The spray gun leaks
Internal parts of the gun are worn or dirty.
•
The nozzle
The nozzle was assembled incorrectly.
•
assembly leaks
A seal is dirty.
•
The spray gun will
The spray nozzle is plugged.
•
not spray.
The spray nozzle is blocked (if fitted)
•
The spray tip is in the reverse position.
Remedy
•
Plug the sprayer in.
•
Perform pressure relief procedure and set selector
switch back to SPRAY
•
Properly test the power supply voltage.
•
Replace the extension cord.
•
Switch the device off, turn the selector switch to the
PRIME position (vertical), remove the mains plug and
allow device to cool down for min. 30 minutes. Eliminate
the cause of overheating, e.g. covered ventilation slot.
•
Please contact Wagner Service
•
Try to prime the unit again.
•
Refill the bucket or immerse the suction tube in paint.
•
Clean the suction tube.
•
Clean the inlet filter.
•
Tighten it securely.
•
Follow the instructions in the chapter "Help with
suction problems".
•
Replace
•
Please contact Wagner Service
•
Replace the spray nozzle with a new nozzle.
•
Clean the inlet filter.
•
Clean or replace the filter.
•
Thin or strain the paint.
•
Replace
•
Please contact Wagner Service
•
Check the tip assembly and assemble properly
•
Clean the seal.
•
Clean the spray nozzle and use the HEA filter set.
•
Clean or replace the filter.
•
Put the nozzle in the forward position.
EN
27
