Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ENGLISH
Insert pin straight and seat firmly against drywall surface
u
as shown in Figure B. The drywall pin should always be
pushed in by hand and never driven by a hammer.
@
To remove drywall pin from the wall, pull out straight.
u
CAUTION: Always be sure drywall pin is closed
when not in use.
Horizontal or vertical line projection on a wall
1. Hands free operation of the laser:
Attach drywall pin to the wall per instructions under
u
"Drywall Pin" section. Always make sure drywall pin is
securely attached to the wall.
Move on/ off switch (3) actuator to the "On" position to
u
project the laser line.
Rotate the laser to center horizontal (7) or vertical (6)
u
bubble vials. Be sure the laser is firmly attached to the
drywall pin before removing support.
2. Operation of the laser:
Hold the laser firmly against the wall.
u
Move on/ off switch (3) actuator to the "On" position to
u
project the laser lines.
Align laser line with appropriate mark on your work
u
surface, rotate the laser to center horizontal (7) or vertical
(6) bubble vials. Realign laser with mark if necessary.
Figure C illustrates a typical application for the Laser Level
u
when it is wall mounted.
Angular line projection on a wall
Operation of the laser:
Attach drywall pin to the wall per instructions under
u
"Drywall Pin" section. Always make sure drywall pin is
securely attached to the wall.
Rotate the laser to center horizontal (7) or vertical (6)
u
bubble vials.
Turn protractor ring to align "0" mark with Alignment
u
Indicator (9).
Rotate laser until indicator (9) is at desired angle.
u
Move on/ off switch (3) actuator to the "On" position to
u
project the laser line.
Straight line projection on any flat surface
Free hand operation of the laser:
Hold the laser firmly against a flat surface.
u
Move on/off switch (3) actuator to the "On" position to
u
project the laser line.
Align laser line with appropriate marks on your work
u
surface (common use is laying tiles or marking plywood
for cutting purpose).
DANGER: Laser radiation, avoid direct eye exposure.
6
(Original instructions)
Helpful hints
If the laser light becomes dim or is no longer visible
u
when the switch is in the on position check or change the
battery.
The laser lines are only level on the wall against which
u
the unit is held or hung. The short line visible on any
adjacent wall is not level. The same is true for straight line
projection on a floor or wall, the short line on any adjacent
wall is not level.
The laser unit should never be used as a spirit (bubble)
u
level. The levels are only calibrated to the laser line when
held or hung against a vertical surface.
The laser unit only generates level lines when held or
u
hung against a vertical surface.
Make sure laser is as square as possible to flat surface to
u
ensure proper line projection.
Storage
Always store the laser level indoors.
Maintenance
Your BLACK+DECKER equipment has been designed to
operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper equipment care and regular cleaning.
Warning! Before performing any cleaning or maintenance on
the equipment ensure equipment is switched off and batteries
removed.
Regularly clean housing using a damp cloth. Do not use
u
any abrasive or solvent-based cleaner.
@
Accessories
Warning! The use of any accessory not recom-
mended for use with this equipment could be
hazardous.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Laser diode wavelength:
Laser output type:
Laser output power:
REVBDLL100 Type 1
630 - 680 nm (red color)
Continuous wave (CW)
< 2.2mW
Tabla de contenido
