Remote Control Via Lc-3 Or Lc-9Rtx; Operation Via Dmx Light Controller; Dmx Connection - IMG STAGELINE TWIST-50LED Manual De Instrucciones

chain. See chapter 6.1 "DMX connection", how-
GB
ever, skip step 1.
2) The first TWIST-50LED in the chain (of which
the jack DMX INPUT has not been connected) is
used as a master unit to control the slave units.
Set the slave units to one of the two slave
modes:
a) Press the button MENU (7) repeatedly until
the display shows
b) Activate the menu item
ENTER. The slave mode adjusted starts
flashing on the display:
Slave mode 1: The slave unit is syn-
chronized with the master unit.
Slave mode 2: The movement of the
head of the slave unit is temporarily
opposite to the master unit.
c) Press the button
slave mode. To memorize, press the button
ENTER.
d) To exit the setting mode, keep the button
MENU pressed until the moving head starts
the show program or wait for one minute and
do not press any button.
Once the slave units receive the control signals
from the master unit, the red LED SLAVE (8)
lights up on the slave units.

5.4 Remote control via LC-3 or LC-9RTX

The cable remote controller LC-3 or the wireless
remote controller LC-9RTX available as an acces-
sory allow to control different functions.
1) Connect the remote controller LC-3 to the jack
ONLY FOR REMOTE CONTROL (11) or con-
nect the wireless receiver of the LC-9RTX to the
jack ONLY FOR WIRELESS RECEIVER (12).
2) No DMX signal must be present at the DMX
INPUT (10). The yellow LED MASTER (6) must
light up.
3) The DMX OUTPUT (13) allows to connect further
TWIST-50LED moving heads (
in order to control them together with the master
unit via the remote controller.
4) To activate or deactivate the light beam, press
the button STAND BY on the remote controller.
At the same time, the head returns to its starting
position. When the light beam is deactivated, the
LED of the button STAND BY lights up as an
indication.
5) Press the button MODE on the remote controller
to select the operating mode:
16
(Slave Mode).
with the button
or to select the desired
chapter 5.3)
1. If the LED of the button MODE does not light
up, keep the button FUNCTION on the re-
mote controller pressed to activate one of the
three stroboscope functions:
A permanent stroboscope
B stroboscope alternating on master unit and
slave units
C music-controlled stroboscope
Activate the music control for this purpose
( chapter 5.1).
Each time you keep the button FUNCTION
pressed again, the next stroboscope function
is activated.
2. When the LED of the button MODE starts
flashing, press the button FUNCTION to
select the show program (Sh 1 – 4).
3. When the LED of the button MODE lights up,
press the button FUNCTION to select the
colour of the light beam and the light pattern.
To select the colour, only press the button
briefly; to select the pattern, keep the button
pressed until the next pattern appears. In this
mode, the moving head controls the move-
ment of the light beam automatically, i. e.
independently of the music.

6 Operation via DMX light controller

For operation via a light controller with DMX 512
protocol (e. g. DMX-1440 or DMX-510USB from
"img Stage Line"), the TWIST-50LED is equipped
with 11 DMX control channels. If not all functions
are required, it can be switched to the 8-channel
mode. For the functions and the DMX values see
chapter 9.1.
DMX is the abbreviation of digital multiplex and means dig-
ital control of several DMX units via a common control
cable.

6.1 DMX connection

For DMX connection, 3-pole XLR connectors with
the following pin configuration are provided:
Pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, special cables for high data flow
are recommended. Standard microphone cables
with screening and a minimum cross section of
2 × 0.22 mm and with a capacity as low as possible
2
can only be recommended for a total cable length
of up to 100 m. For cable lengths exceeding 150 m,
it is generally recommended to insert a DMX level
matching amplifier (e. g. SR-103DMX from "img
Stage Line").