Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Worklight
The worklight (6) is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Speed Selector
Low Mode
Normal Impacting
High Mode
High Speed Impacting
Usage
Warning!Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it con tains no
cracks.
CAUTION: Ensure fastener and/or system will withstand the
level of torque generated by the tool. Excessive torque may
cause breakage and possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press variable speed trigger switch (3) to start operation.
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the fastening
torque is affected by many factors including the following:
Voltage: Low voltage, due to a nearly discharged
-
battery, will reduce fastening torque.
Accessory size: Failure to use the correct accessory
-
size will cause a reduction in fastening torque.
Bolt size: Larger bolt diameters generally require
-
higher fastening torque. Fastening torque will also
vary according to length, grade, and torque coefficient.
Bolt: Ensure that all threads are free of rust and other
-
debris to allow proper fastening torque.
Material: The type of material and surface finish of the
-
material will affect fastening torque.
Fastening time: Longer fasten ing time results in
-
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners to
be overstressed, stripped or damaged.
Accessories
Warning!Since accessories, other than those offered by
STANLEY, have not been tested with this product, use of
such accessories with this tool could be hazardous. To reduce
the risk of injury, only STANLEY recommended accessories
should be used with this product.
SBW920
RPM
RPM
(Original instructions)
Maintenance
Your STANLEY tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
0–900
Regularly clean the ventilation slots in your tool and
u
0–1900
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior.
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available
atwww.2helpU.com
Technical data
Voltage
No-load speed
Impact
Max. torque
(PTI Method)
Anvil Size
Weight
Charger
Input
V
Voltage
AC
Output
V
Voltage
DC
Current
A
V
DC
-1
Min
IPM
Nm
mm
kg
SC125
SC200
AR , B2
AR / B2
220V
220V
B3
B3
120V
120V
BR
BR
BIVOLT
127V
(127V | 220V)
18V
18V
（20V MAX）
（20V MAX）
1.25
2
ENGLISH
SBW920
18V (20V MAX)
0 - 900 / 1900
0 - 3100
370
12.7 (Hog Ring)
1.6
SC400
AR / B2
220V
B3
120V
BR
127V
18V
（20V MAX）
4
25
Tabla de contenido
