Additional Information - Denon AVR-1802 Instrucciones De Operación

ENGLISH

18 ADDITIONAL INFORMATION

Speaker setting examples
Here we describe a number of speaker settings for different purposes. Use these examples as guides to set up
your system according to the type of speakers used and the main usage purpose.
(1) Basic setting
Use this setting if your main purpose is to listen to movie music and when using one set (two speakers) of
regular single-way or two-way speakers as the surround speakers.
Front speakers • Set the front speakers with their front surfaces as
Monitor
flush with the TV or monitor screen as possible.
Set the center speaker between the front left and
right speakers and no further from the listening
Center speaker
Subwoofer position than the front speakers.
• Consult the owner's manual for your subwoofer
45°
for advice on placing the subwoofer within the
listening room.
• If the surround speakers are direct-radiating
(monopolar) then place them slightly behind and at
an angle to the listening position and parallel to the
120°
walls at a position 60 to 90 centimeters (2 to 3 feet)
Surround speakers above ear level at the prime listening position.
As seen from above
(2) Using diffusion type speakers for the surround speakers
For the greatest sense of surround sound envelopment, diffuse radiation speakers such as bipolar types, or
dipolar types, provide a wider dispersion than is possible to obtain from a direct radiating speaker (monopolar).
Place these speakers at either side of the prime listening position, mounted above ear level.
Path of the surround sound from the • Set the front speakers, center speaker and subwoofer
speakers to the listening position
in the same positions as in example (1).
• Set the surround speakers directly at the sides of
the listening position and 60 to 90 centimeters (2
to 3 feet) above ear level.
• The signals from the surround channels reflect off
the walls as shown on the diagram at the left,
creating an enveloping and realistic surround sound
presentation.
As seen from above
Surround
The AVR-1802 is equipped with a digital signal processing circuit that lets you play program sources in the surround
mode to achieve the same sense of presence as in a movie theater.
Dolby Surround
(1) Dolby Digital (Dolby Surround AC-3)
Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories.
Dolby Digital consists of up to "5.1" channels - front left, front right, center, surround left, surround right,
and an additional channel exclusively reserved for additional deep bass sound effects (the Low Frequency
Effects – LFE – channel, also called the ".1" channel, containing bass frequencies of up to 120 Hz).
Unlike the analog Dolby Pro Logic format, Dolby Digital's main channels can all contain full range sound
information, from the lowest bass, up to the highest frequencies – 22 kHz. The signals within each channel
are distinct from the others, allowing pinpoint sound imaging, and Dolby Digital offers tremendous dynamic
range from the most powerful sound effects to the quietest, softest sounds, free from noise and distortion.
24
2 Dolby Digital and Dolby Pro Logic
Comparison of home surround systems
No. recorded channels (elements)
No. playback channels
Playback channels (max.)
Audio processing
High frequency playback limit of surround
channel
Surround speaker
Front speaker
2 Dolby Digital compatible media and playback methods
60 to 90 cm
Marks indicating Dolby Digital compatibility:
The following are general examples. Also refer to the player's operating instructions.
As seen from the side
Media
LD (VDP)
DVD
Others
(satellite broadcasts, CATV, etc.)
1 Please use a commercially available adapter when connecting the Dolby Digital RF (AC-3RF) output jack
of the LD player to the digital input jack.
Please refer to the instruction manual of the adapter when making connection.
2 Some DVD digital outputs have the function of switching the Dolby Digital signal output method between
Surround speaker
"bit stream" and "(convert to) PCM". When playing in Dolby Digital surround on the AVR-1802, switch
Front speaker
the DVD player's output mode to "bit stream". In some cases players are equipped with both "bit stream
60 to 90 cm
+ PCM" and "PCM only" digital outputs. In this case connect the "bit stream + PCM" jacks to the AVR-
1802.
As seen from the side (2) Dolby Pro Logic
• Dolby Pro Logic
logic steering technology and offering improvements over conventional Dolby Pro Logic circuits.
• Dolby Pro Logic
regular stereo sources into five channels (front left, front right, center, surround left and surround right) to
achieve surround sound.
• Whereas with conventional Dolby Pro Logic the surround channel playback frequency band was limited,
Dolby Pro Logic
channels were monaural (the surround left and right channels were the same) with previous Dolby Pro
Logic, but Dolby Pro Logic
• Various parameters can be set according to the type of source and the contents, so it is possible to
achieve optimum decoding (see page 16).
Sources recorded in Dolby Surround
These are sources in which three or more channels of surround have been recorded as two channels of
signals using Dolby Surround encoding technology.
Dolby Surround is used for the sound tracks of movies recorded on DVDs, LDs and video cassettes to be
played on stereo VCRs, as well as for the stereo broadcast signals of FM radio, TV, satellite broadcasts
and cable TV.
Decoding these signals with Dolby Pro Logic makes it possible to achieve multi-channel surround
playback. The signals can also be played on ordinary stereo equipment, in which case they provide
normal stereo sound.
There are two types of DVD Dolby surround recording signals.
q 2-channel PCM stereo signals
w 2-channel Dolby Digital signals
When either of these signals is input to the AVR-1802, the surround mode is automatically set to Dolby
Pro Logic II when the "DOLBY/DTS SURROUND" mode is selected.
Dolby Digital
5.1 ch
5.1 ch
L, R, C, SL, SR, SW
Digital discrete processing Dolby Digital
(AC-3) encoding/decoding
20 kHz
and
Dolby Digital output jacks
Coaxial Dolby Digital RF output jack
1
Optical or coaxial digital output
(same as for PCM)
2
Optical or coaxial digital output
(same as for PCM)
II
II is a new multi-channel playback format developed by Dolby Laboratories using feedback
II can be used to decode not only sources recorded in Dolby Surround (
II
offers a wider band range (20 Hz to 20 kHz or greater). In addition, the surround
II
they are played as stereo signals.
Dolby Pro Logic
2 ch
4 ch
L, R, C, S (SW - recommended)
Analog matrix processing Dolby Surround
7 kHz
.
Playback method (reference page)
Set the input mode to "AUTO".
(Page 13,14)
Set the input mode to "AUTO".
(Page 13,14)
Set the input mode to "AUTO".
(Page 13,14)
) but also