Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
Attaching and Removing the Blade (Fig. B)
1. Retract lower guard
7
outer blade clamp washer
2. Depress the spindle lock button
blade retaining bolt
12
the blade lock engages and the blade stops rotating.
nOTE: Hex wrench is stored on the saw as shown in
Figure A.
3. Tighten the blade retaining bolt securely with the
hex wrench.
nOTE: Bolt has a right‑handed thread. To loosen, turn
counterclockwise. To tighten, turn clockwise.
nOTE: Never engage the blade lock while the saw is
running, or engage in an effort to stop the tool. Never
turn the tool on while the blade lock is engaged. Serious
damage to your saw will result.
Supporting Large Panels/Securing
Workpiece (Fig. C–F)
Support large panels to minimize the risk of blade pinching
and kickback. Large panels tend to sag under their own
weight as shown in Figure C.
Supports must be placed under the panel on both sides, near
the line of cut and near the edge of the panel (Figure D).
WARNING: To reduce the risk of injury Never hold the
piece being cut with your hands or lay it across your
leg (Figure E).
Secure the workpiece to a stable platform as shown in
Figure F. It is important to support the work properly to
minimize body exposure, blade binding, or loss of control.
Cutting Depth Adjustment (Fig. G, H)
The depth of cut should be set according to the thickness of
the workpiece.
1. Loosen the depth adjustment lever
saw shoe
5
.
2. Align the saw shoe with the desired depth of cut
indicated on the scale markings on the depth strap.
3. Set depth adjustment of saw such that one tooth
the blade projects below the workpiece
Figure H.
4. Tighten the depth adjustment lever to lock the saw shoe
in place.
Bevel Angle Adjustment (Fig. I)
This tool can be set to bevel angles between 0° and 56°.
1. Loosen the bevel adjustment lever
shoe
5
.
2. Move the saw shoe into the desired position
corresponding with the bevel angle markings on
the bevel angle scale (
3. Tighten the bevel adjustment lever to lock the saw shoe
in place.
4. Confirm the accuracy of the setting by checking the
bevel angle of an actual cut on a scrap piece of material.
10
and assemble saw blade
11
as shown in Figure B.
14
while turning the
with the hex wrench
17
13
to unlock the
20
as shown in
9
to unlock the saw
10
.
)
Shoe Adjustment for 90° Cuts (Fig. J)
6
and
The shoe
5
blade is perpendicular to the shoe at 0° bevel setting.
If realignment is needed:
until
1. Adjust the saw to 0° bevel.
2. Retract lower blade guard
3. Loosen bevel adjustment lever
the blade
4. Turn the calibration screw
at the proper angle.
5. Confirm the accuracy of the setting by checking the
squareness of an actual cut on a scrap piece of material.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. K)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
16
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. L)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
19
of
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
3
and one hand on the secondary handle
CUTTING SPECIFICATIONS
Bevel angle
Blade size
Max cut depth, 45° bevel
Max cut depth, 0° bevel
RPM no load
On/Off Switch (Fig. A)
Saw is equipped with a switch lock‑off feature to prevent
unintentional operation.
has been set by the factory to assure that the
7
.
9
6
and shoe to adjust the 90° setting.
21
so that the shoe will stop
15
into the tool handle, align the
. Place a square against
4
.
0° and 56°
7-1/4" (184 mm)
1-31/32" (50mm)
2-9/16" (65mm)
5000
Tabla de contenido
