Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
7. Release the on/off switch
stop completely before withdrawing the blade from
the material.
8. When starting each new cut, repeat the above steps.
Ripping
Ripping is the process of cutting wider boards into
narrower strips – cutting grain lengthwise. Hand guiding
is more difficult for this type of sawing and the use of a
PORTER‑CABLE rip fence is recommended. A rip guide is
available at extra cost from your local dealer or authorized
service center.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your PORTER‑CABLE power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by PORTER‑CABLE, have not been tested with this
product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
PORTER‑CABLE recommended accessories should be
used with this product.
Recommended accessories for use with your
product are available at extra cost from your local
dealer or authorized service center. If you need
assistance in locating any accessory, please contact
PORTER‑CABLE call 1‑888‑848‑5175 or visit our website:
www.portercable.com.
Dust Extraction (Fig. A)
WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dust mask.
A dust extraction port
18
The dust extraction port allows you to connect the tool to an
external dust extractor, either using the AirLock™ system, or a
standard 32 mm dust extractor fitment.
WARNING: ALWAYS use a vacuum extractor designed
in compliance with the applicable directives regarding
dust emission when sawing wood. Vacuum hoses of
12
1
and allow the blade to
is supplied with your tool.
most common vacuum cleaners will fit directly into the
dust extraction outlet.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a PORTER‑CABLE factory service center
or a PORTER‑CABLE authorized service center. Always
use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.portercable.com
Three Year Limited Warranty
PORTER‑CABLE will repair or replace, without charge, any
defects due to faulty materials or workmanship for three
years from the date of purchase (two years for batteries).
This warranty does not cover part failure due to normal wear
or tool abuse. For further detail of warranty coverage and
warranty repair information, visit www.portercable.com
or call 1‑888‑848‑5175. This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty PORTER‑CABLE tools are covered
by our:
1 YEAR FREE sERViCE
PORTER‑CABLE will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your PORTER‑CABLE Power Tool or Nailer for any reason, you
can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
Tabla de contenido
