Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ASSEMBLY (Fig. A1, A2, A3, A4)
There are three positions on the machine for different use,
standing, folding and transporting. The legs are locked using
twist knobs which lock/unlock in either direction and have a
central unlocked position.
1. Start with the saw standing on its wheels (Fig. A1), unlock
the upper legs. Swing up the legs and lock (Fig. A2) then
unlock the lower legs.
2. Lift the table from the end (Fig. A3), allowing the lower leg
to swing into place. Swing the leg fully into place and lock
(Fig. A4).
3. There is a adjustable spring leg as shown in Fig. A5. You can
rotate it clockwise or anti‑clockwise for your desired length.
(Fig. A5).
Folding Instructions (Fig. B1, B2, B3, B4)
Hold and support the table edge, unlock the legs at the wheel
end (Fig. B1).Lower the wheels to the ground, allowing the legs
to swing under (Fig. B2). Stand the table on end, fold up and
lock the lower legs, unlock the upper legs (Fig. B3). Swing down
the legs and lock (Fig. B4).
To Transport the Table Saw (Fig. C1, C2)
WARNING! Cover the upper part of the saw blade during
transportation, for example by the guard.
The upper legs could be locked in the vertical position for use as
a trolley handle.
Blade Elevation Handle Assembly (Fig. D)
Place washer
24
, housing
the bolt
28
to assemble the blade elevation handle
Riving Knife Set‑Up (Fig. E, F, G)
WARNING! Disconnect the mains cable! The setup of the
riving knife
3
must be checked before each use.
WARNING! The riving knife
correct position for through cutting. However, before first
use and before connecting the machine to the power,
make sure the riving knife is secure, in-line with the blade
and the correct distance from the blade (refer to Fig F).
Only work with the machine if the riving knife
upper position unless the saw is being used for slitting
operations. THE GUARD MUST BE REMOVED FOR SLITTING
OPERATIONS. IMMEDIATELY RAISE THE RIVING KNIFE
AND REATTACH THE GUARD AFTER COMPLETING ANY
OPERATION WHICH REQUIRES REMOVAL OF THE GUARD
OR LOWERING OF THE RIVING KNIFE.
1. Set the saw blade
4
to the max. cutting depth, put it at
00 position and lock it.
2. Remove the table insert
WARNING! For transport reasons, the riving knife
fixed in the lower position before initial commissioning.
Only work with the machine if the riving knife is in the
upper position. Fitting the riving knife in the upper position
is as follows:
25
, washer
26
and hex nut
11
3
should be delivered in the
3
(Fig. E).
20
3. Loosen the locking handle
in the upper position (Fig. F).
4. The gap between the saw blade
knife should be around 3 mm to 5 mm (Fig. G).
5. Retighten the mounting screw
insert
20
WARNING! Ensure the machine is disconnected from the
power source. Never use the machine without the table
insert; Immediately replace the table insert when worn
or damaged.
WARNING! If the locking handle cannot be positioned in
the lower quadrant locked position the riving knife may
not be correctly located. Reposition the riving knife and
reset the locking handle in the lower quadrant position.
WARNING! The locking handle must be in the lower
quadrant, below horizontal position, to be fully locked.
Check this carefully.
Saw Blade Guard Assembly (Fig. H)
WARNING! The riving knife must be locked in the upper
position before fitting the guard.
The guard must not be fitted when the riving knife is located
and locked in the lower position.
•
The blade guard
pin
39
to locate and secure the guard to the riving knife
The guard must be fitted when making through cuts to
reduce the risk of injury.
•
Raise the saw blade and riving knife assembly by turning
the blade elevation handle
27
on
figure E.
.
•
Locate the bar in the rear of the guard
the rear of the riving knife location.
•
Press the locking pin
the riving knife front location.
•
Release the locking pin and confirm the guard is secure on
the riving knife.
•
The operator should only be able to remove the guard from
the riving knife by depressing the locking pin
lifting the guard upwards.
•
Gently tug the guard up from riving knife to ensure this is
is in the
fully fitted.
Saw Blade Assembly/Replacement
(Fig. E, H, I)
WARNING! Always check alignment of riving knife and
function ality of guards after any maintenance.
WARNING! Always check the Riving knife is locked in
position and aligned with the blade before each use and
after any maintenance. The guard must be fitted when
3
was
making through cuts.
WARNING: Ensure the machine is disconnected from the
power source. Wear the safety gloves.
WARNING: Do not run saw if the dust door has
been removed.
29
and push the riving knife
teeth and the riving
4
29
and fix the table
.
2
is supplied with a spring‑loaded locking
11
anti‑clockwise as shown in
and lower the guard to align with
39
ENGLISh
3
3
.
2
downwards and to
39
and then
35
Tabla de contenido
