Rear Panel - FONESTAR MPZ-461 Manual De Usuario

MUTE
6 7
8.- Z1-Z4: allows the signal from the MP3 module to be assigned to one or more output zones. When a
zone is selected, the corresponding button illuminates.
9.- Indicator light that lights up when the audio output of the input channel is deactivated.
10.- MUTE: button that activates/disables the audio output of the corresponding input channel.
11.- MONITOR LEVEL: a rotating dial that regulates the volume of the monitor output.
12.- Z1-Z4: to assign the input signal corresponding to one or more exit zones. When a zone is selected,
1 2 3
the corresponding button illuminates.
13.- Signal level indicators for the corresponding output.
MODE
14.- MON Z1-Z4: you can select which zone you want to listen to with the MONITOR output. When a zone
REC
is selected, the corresponding button is illuminated.
10 9
15.- ZONE 1-4 LEVEL: a rotating dial that regulates the output volume of each zone.
16.- ON/OFF: on/off switch.

REAR PANEL

1 2
MONITOR PRIORITY
8 , 1 W
T
+ -
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION: SHOCK HAZARD - DO NOT OPEN
RISK OF FIRE-REPLACE FUSE AS MARKED
GND LIFT
MPZ-461
MULTI-ZONE AMPLIFIER
4 x 90 W RMS
~ 230 V AC. 50/60 Hz FUSE: T6.3AL 250 V
POWER CONSUMPTION: 450 W
7
8
1.- MONITOR (1 W, 8 Ω): output for connection of a low impedance loudspeaker 8 Ω to monitor the output.
2.- PRIORITY: when closing the contacts of these two terminals, the order of priority of the inputs changes.
The order of priority without closing the contacts is as follows:
TEL.PAGING > MIC 1 > M-46 Microphone > MIC 2, MIC 3, LINE 4, LINE 5, MP3 Module.
The order of priority when closing the contacts is as follows:
MIC 1 > TEL.PAGING > M-46 Microphone > MIC 2, MIC 3, LINE 4, LINE 5, MP3 Module.
3.- TEL. PAGING: telephone input connection terminals. These allow you to connect to a telephone
switchboard to prioritize paging over other inputs. Make the connection between terminals T and G.
Consult the characteristics of the control unit to adjust to the input level of the amplifier.
4.- FM ANT: FM antenna input.
5.- REC OUT: balanced or unbalanced line output. Signal output for recording, mixer, power stage, etc.,
screw terminal connections. general speaker output. For connection of low impedance 4 Ω and high
impedance 100 or 70 V lines, connect the speaker line between the COM terminal and the desired
impedance or V line.
6.- OUTPUT: loudspeaker general output. For the connection of low impedance loudspeakers 4 Ω and in
high impedance lines of 100 or 70 V, connect the loudspeaker line between the COM terminal and the
impedance or line in V required.
7.- GND LIFT: this switch is normally in the GND position. If there are grounding noises, switch to the LIFT
position, disconnecting the device from the ground.
8.- AC power socket.
9.- ZONE: microswitches to select in which zone or zones the TEL PAGING input will be heard.
10.- VOLUME: a rotating dial that regulates the volume of the TEL PAGING input.
11.- CH 4, CH 5: line level inputs. Allow for the connection of audio sources, 2 x RCA connectors.
Z1 Z2
-10
-15
Z3 Z4
MONITOR
8 910 11 12 13 14 15
4 5 6
VOL +
VOL -
8 7
3 4 5
TEL PAGING REC OUT
R G FM ANT G - + COM 4
ZONE 1
REC OUT
DO NOT OPEN
G - + COM 4
ZONE 3
PHANTOM +48 V
LINE
LINE
PUSH
CH 5 CH 4 CH 3
TEL.
ZONE
L L
R R
VOLUME GAIN GAIN
9 10 11 12
-10 -10
-15 MON -15 MON
ZONE 1 ZONE 2
6
OUTPUT REC OUT OUTPUT
70 V 100 V G - + COM 4
ZONE 2
OUTPUT REC OUT OUTPUT
70 V 100 V G - + COM 4
ZONE 4
PHANTOM +48 V PHANTOM +48 V
MIC LINE MIC LINE MIC
PUSH PUSH
CH 2 CH 1
GAIN GAIN GAIN
13 14
15
- 3 -
-10 -10
-15 MON -15 MON
ZONE 3 ZONE 4
OUTPUTS
70 V 100 V
70 V 100 V
INPUTS
RS-232
PAGING MIC
M-46 INPUT
17
16
EN
16