Tabla de contenido
Idiomas disponibles
Idiomas disponibles
REAR PANEL
1
BREAKER
POWER CONSUMPTION: 1,000 W
~ 230 V AC. 60 Hz FUSE: 6 A
4
1.- BREAKER: resettable fuse, 6 A. When the amp is overloaded or there is a surge, the fuse will blow to
avoid damage. It is reset by pressing it.
2.- COM: loudspeaker output common terminal (ground).
NOTE: do not connect to the earth.
3.- 4 Ω, 8 Ω, 70 V and 100 V: loudspeaker output terminals. Use only one output depending on the load
impedance: 4-8 Ω low impedance lines or 100 or 70 V high impedance lines. Connect the loudspeakers
between the COM terminal and one of the output terminals; 4 Ω, 8 Ω, 70 V or 100 V.
NOTE: use only one output.
PRÉAMPLIFICATEUR
PREAMPLIFICADOR
PREAMPLIFICADOR
PREAMPLIFIER
4.- AC INPUT: mains input.
5.- INPUT: balanced aux line level signal input. With XLR and 6.3 mm stereo jack connectors. Use just one
input connector.
6.- LINK: balanced aux line level signal output. With XLR and 6.3 mm stereo jack connectors. Another
FS-2601E
power amp can be connected in cascade.
BREAKER
FS-2601
7.- FAN: speeds up the air circulation inside the amplifier to reduce the temperature. The air circulates from
POWER AMPLIFIER
4 x 90 W RMS
POWER CONSUMPTION: 1,000 W
the front to the back. The fan speed depends on the temperature. Do not obstruct the ventilation slot
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: SHOCK HAZARD - DO NOT OPEN
~ 230 V AC. 60 Hz FUSE: 6 A
RISK OF FIRE-REPLACE FUSE AS MARKED
FS-2601E
CONNECTION
BREAKER
FS-2601
POWER AMPLIFIER
4 x 90 W RMS
Connect the loudspeakers to the loudspeaker output. Use the 4-8 Ω low impedance output or the high
POWER CONSUMPTION: 1,000 W
impedance 100 or 70 V line output, depending on the type of loudspeakers you are going to connect. Do not
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: SHOCK HAZARD - DO NOT OPEN
RISK OF FIRE-REPLACE FUSE AS MARKED
~ 230 V AC. 60 Hz FUSE: 6 A
use both types of output at the same time.
If you use the low impedance output, you must connect the loudspeakers in a series/parallel circuit so that
the load impedance in the loudspeakers is the same as the amplifier output impedance and the power
supplied by the amplifier does not exceed that withstood by the loudspeakers.
If you use the high impedance 100 or 70 V lines, you must connect all the loudspeakers in parallel and the
sum of the power of all the loudspeakers must not exceed the power supplied by the amplifier.
Once all the connections have been made according to your needs, connect the equipment to the mains and
switch it on. After use, do not forget to switch the equipment off and disconnect it from the mains.
2
OUTPUT
COM
FS-2601
POWER AMPLIFIER
4 x 90 W RMS
INPUT
PUSH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: SHOCK HAZARD - DO NOT OPEN
RISK OF FIRE-REPLACE FUSE AS MARKED
OUTPUT
COM
4
8
70 V
100 V
INPUT
LINK
PUSH
PUSH
OUTPUT
COM
4
8
70 V
100 V
INPUT
LINK
PUSH
PUSH
3
4
8
70 V
LINK
PUSH
5
6
BREAKER
100 V
PROT
TEMP
100 V
100 V
100 V
100 V
7
100 V
100 V
Tabla de contenido
