Tabla de contenido
Idiomas disponibles
Idiomas disponibles
REAR PANEL
1
MXZ-2036
MULTIZONE MIXER/PREAMPLIFIER
~230 V AC, 50 Hz
FUSE: T1AL 250 V
1.-
AC socket: for the connection of AC power supply cable.
2.-
+24 V DC ZONE ATT PRIORITY OUT: output control relay. During the sending of messages from the microphone
mod. M-203 a 24 V DC tension will be activated between the negative terminal and the active zones (1 to 6).
3.-
BGM+PAGING OUT: background music and paging combined line output.
4.-
BGM OUT: background music line output.
5.-
PAGING OUT: line output for paging from the remote microphone mod. M-203.
6.-
PLAY MESSAGE: to select the message to be played. Short circuit of COM and M1 terminals to select prerecorded
message number or terminals COM and M2 to select the prerecorded message number 2.
The messages are only played through the PAGING OUT paging output.
7.-
MESSAGE - REC: to select the message to be recorded. Allows selection of the message that is to be recorded
using the message recorder located on the front of the device.
8.-
MESSAGE - REPEAT: to select message playback mode: ON the message is repeated once and OFF the
message is repeated until the STOP button is pressed.
9.-
MESSAGE - PLAY MODE: to select the zones for playback of the messages. In NORMAL mode the message
will only be broadcast in the activated zones, in ALARM mode the message will be broadcast in all the zones at
maximum volume even if they are deactivated.
10.-
MESSAGE - VOLUME - REC: message recording volume control.
11.-
MESSAGE - VOLUME - PLAY: message playback volume control.
12.- 48 V phantom power supply switch. This switch has two positions:
- PHANTOM +48 V: in this position, the MIC input can be connected to an electret condenser microphone
which requires 48 V phantom power supply.
- MIC: in this position, the MIC input can be connected to a low impedance dynamic microphone 30 - 600 Ω
which does not require phantom power supply.
13.-
CHIME VOLUME: chime volume control.
14.-
PRIORITY: priority terminals. Closing these contacts attenuates the level of the auxiliary input (AUX 1, AUX 2 or
AUX 3) and the chimes are activated. Microphone paging and messages will have priority.
15.-
INPUTS - BGM: background musicline signal input or background music amplifier.
16.-
INPUTS - PAGING: paging line signal input or paging amplifier.
17.-
OUTPUTS - ZONE 1-ZONE 6: zones 1-6 output, to connect the loudspeakers or corresponding amplifiers to
each zone, euroblock connectors.
18.-
AUX 1/AUX 2/AUX 3: signal source inputs, 2 x RCA connectors, selectable using the control on the front panel
AUX 1/AUX 2/AUX 3.
19.-
MIC: microphone input with XLR connector, admits signals from balanced and unbalanced microphones and balanced
condenser microphones which require 48 V phantom power supply, present in pins 2 and 3 of the XLR connector.
The microphone connected to the MIC input will only be sent to the zones activated for the BGM+PAGING OUT output.
In the configuration of the system as a 100 V line switching unit the microphone audio will be broadcast through
the background music amplifier.
CAUTION: when connecting and disconnecting an unbalanced microphone the switcher must be in the MIC
position. If the switcher is in the PHANTOM +48 V position this could cause damage to the microphones. When
using microphones which do not require phantom power supply, make sure the switcher is put in the MIC position,
given that the voltage present in pins 2 and 3 of the XLR connector could cause damage to the microphones.
2
+24 V DC ZONE ATT PRIORITY OUT
- 1 +
- 2 +
- 3 +
- 4 +
- 5 +
- 6 +
BGM
PAGING
ZONE 1
ZONE 2
-
+
-
+
-
+
-
+
INPUTS
15
16
3
4
5
6
BGM+PAGING
BGM OUT
PAGING OUT
PLAY MESSAGE
OUT
-
+
-
+
-
+
COM M1
M2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
-
+
-
+
-
+
-
+
OUTPUTS
17
- 3 -
7
8
9
10 11
PLAY MODE
REC
REPEAT
VOLUME
REC
PLAY
3 2 1 OFF
MESSAGE
AUX 1
AUX 2
AUX 3
MIC
GAIN
GAIN
INPUTS
18
19
20 21 22
EN
12
13
14
PRIORITY
CHIME
VOLUME
REMOTE
MIC
VOLUME
23
Tabla de contenido
