Mixer Section - Gemini CDM-3250 Manual De Instrucciones

MIXER SECTION:

23
CHANNEL INPUT SELECTOR: The CHANNEL INPUT SELEC-
TOR switches allow you to choose which input will be con-
trolled by that channels corresponding volume FADER. For ex-
ample CHANNEL (1) INPUT SELECTOR allows you to choose
between line (1) (That sides internal CD player), line (2) which is
line input RCA (1). The same applies for channel 2.
24
CHANNEL ROTARY GAIN: The CHANNEL ROTARY GAIN al-
lows you to boost the signal of each individual channel de-
pending on how low or high its input level is.
25
2-BAND EQUALIZER: The 2-BAND EQUALIZER adjusts the
tone of each CHANNEL by giving you a choice 2 frequencies
(BANDS) to adjust, from LOW and HIGH's, you can use the
adjustment knobs to raise or lower the 2 separate frequencies
until the sound of the music program is appropriate for your
listening environment.
26 CHANNEL VOLUME FADER: After you have chosen which in-
put you will use with the INPUT SELECTOR the corresponding
CHANNEL FADER will allow you to adjust the volume for that
particular CHANNEL.
27 CHANNEL CUE SELECTOR: The CHANNEL CUE SELECTOR
allows you to choose which channel you wish to monitor in
your headphones, to the left is CHANNEL (1) to the right is
CHANNEL (2) and the middle position is BOTH (1 & 2).
CUE VOLUME ROTARY KNOB: The CUE VOLUME ROTARY
28
KNOB adjusts your HEADPHONE MONITOR OUTPUT'S vol-
ume.
29 MICROPHONE VOLUME ROTARY KNOB: Allows you to adjust
the volume of the microphone signal.
30
MASTER VOLUME ROTARY KNOB: The MASTER VOUME
rotary knob adjusts the volume of the MAIN MASTER output.
31
VU METER: The CDM-3250 has a stereo VU METER that al-
lows you to monitor the decibel levels of the LEFT and RIGHT
MASTER output.
32
FADER START BUTTON: The Fader Start function allows you
to start CD playback simply by moving the CROSSFADER from
side to side.
A. Cue up the CD player you wish to start using the Fader
Start function
B. Move the CROSSFADER all the way to the opposite side
of the CD you have just cued.
C. Press the FADER START SELECTOR button so that the
button becomes illuminated.
D. At the point in which you wish to start the audio from the
Cued CD, simply move the CROSSFADER in the direction
of the Cued CD player, and playback will begin.
E. When the CROSSFADER is moved all the way to the
opposite side of the currently playing disc, the unit will stop
playing that disc and return to the beginning of the track or
the set cue point.
6
CROSS FADER: The CROSS FADER allows you to mix evenly
33
from one source to another. The CROSS FADER on the CDM-
3250 is also removable and if the need arises can be replaced.
The RG-45 (RAILGLIDE™) DUAL-RAIL CROSS FADER, which
has internal dual stainless steel rails that allow the slider to ride
smoothly and accurately from end to end can be purchased from
your local GEMINI dealer.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE
THE FADER BACK AND FORTH. PRESSING DOWN ON THE
CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS OF
SOUND.
FADER REPLACEMENT:
1. UNSCREW THE FADER SCREWS. DO NOT TOUCH INSIDE
SCREWS CAREFULLY REMOVE OLD CROSS FADER AND UN-
PLUG CABLE.
2. PLUG IN THE NEW CROSS FADER INTO CABLE AND PLACE
BACK INTO MIXER.
3. SCREW THE CROSS FADER TO MIXER WITH THE FADER
PLATE SCREWS
4. REPLACE THE FACE OF THE MIXER AND SCREW THE
FOUR SCREWS BACK IN AND REPLACE THE FADER KNOBS.
TROUBLESHOOTING:
- If a disc will not play, check to see if the disc was loaded cor-
rectly (label side up). Also check the disc for excessive dirt,
scratches, etc.
- If the disc turns but there is no sound, check the cable connec-
tions, if they are ok, check your amplifier or receiver.
- If the CD skips, check the CD for dirt or scratches. Do not as-
sume that the CD player is defective. Many CD's are recorded
out of spec and will skip on most or all CD players. Before send-
ing the unit for repair, try playing a CD that you are sure plays
properly.
CDM-3250