DeWalt DWE4016 Traducido De Las Instrucciones Originales página 25

• Make sure the disc or wheel rotates in the direction of the
arrows on the accessory and the tool.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.

WARNING:
• Ensure all materials to be ground or cut are secured
in place.
• Secure and support the workpiece. Use clamps or a
vice to hold and support the workpiece to a stable
platform. It is important to clamp and support the
workpiece securely to prevent movement of the
workpiece and loss of control. Movement of the
workpiece or loss of control may create a hazard and
cause personal injury.
Support panels or any oversized workpiece
•
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of the
workpiece on both sides of the wheel.
• Apply only a gentle pressure to the tool. Do not exert
side pressure on the disc.
• Avoid overloading. Should the tool become hot, let it
run a few minutes under no load condition to cool the
accessory. Do not touch accessories before they have
cooled. The discs become very hot during use.
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the body of the tool, as shown in
Figure F.
Switches

WARNING: Do not switch the tool on or off when
under load.

WARNING: Before using the tool, check that the handle is
tightened securely.
Slider Switch (Fig. A)
To start the tool, slide the on/off slider switch
front of the tool. To stop the tool, release the on/off slider switch.
For continuous operation, slide the switch toward the front of
the tool and press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press the
rear part of the slider switch and release.
Spindle Lock (Fig. A)
The spindle lock
rotating when installing or removing wheels. Operate the
spindle lock only when the tool is turned off, unplugged from
the power supply, and has come to a complete stop.
To engage the lock, depress the spindle lock button and rotate
the spindle until you are unable to rotate the spindle further.
Metal Applications
When using the tool in metal applications, make sure that a
residual current device (RCD) has been inserted to avoid residual
risks caused by metal swarf.
If the power supply is shut off by the RCD, take the tool to an
authorised D

To avoid build‑up of metal swarf inside the machine, we
recommend to clear the ventilation slots on a daily basis. Refer
to Maintenance.
Using Flap Discs

MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
4 ,
satisfactory operation depends upon proper tool care and
regular cleaning.

Pop‑off Brushes
The motor will be automatically shut off indicating that the
carbon brushes are nearly worn out and that the tool needs
1 toward the
servicing. The carbon brushes are not user‑serviceable. Take the
tool to an authorised D
2 is provided to prevent the spindle from
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
WALT repair agent.
e
WARNING: In extreme working conditions, conductive
dust can accumulate inside the machine housing when
working with metal. This can result in the protective
insulation in the machine becoming degraded with a
potential risk of an electrical shock.
WARNING: Metal dust build‑up. Extensive use of flap
discs in metal applications can result in the increased
potential for electric shock. To reduce this risk, insert an
RCD before use and clean the ventilation slots daily by
blowing dry compressed air into the ventilation slots
inaccordance with the below maintenance instructions.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental start‑up can cause injury.
WALT repair agent.
e
EngLIsh
23