Black and Decker Powerful Solutions SMS216 Manual Del Usuario página 9

The blade guard on your saw will automatically raise
when the arm is brought down; it will lower over the
blade when the arm is raised. The guard can be raised
by hand when installing or removing saw blades or for
inspection of the saw. Never raise the blade guard
manually unless the machine is switched off.
Check periodically that the motor air slots are clean and
free of chips.
Do not work with material containing asbestos.
Asbestos is considered to be carcinogenic.
Never make the warning signs on the power tool
unrecognisable.
Never stand on the power tool. Serious injuries could
occur when the power tool tips over or when coming in
contact with the saw blade.
Do not take hold of the saw blade after working before it
has cooled. The saw blade becomes very hot while
working.
Advance the saw blade against the workpiece only
when it is switched on. Otherwise, the danger of kick-
back exists when the saw blade catches in the
workpiece.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
Never place hands near cutting area. Keep hands
outside the "No Hands Zone" which includes entire table
and is labelled by "No Hands" symbols.
To avoid injury from materials being thrown, unplug the
saw to avoid accidental starting, and then remove small
materials.
Before use and after any maintenance the blade guard
must be checked to ensure proper function. This test
must be performed with the saw switched off and
unplugged. The arm must be raised and lowered to
ensure the guard covers the blade and the blade does
not contact the guard. If the guard fails to operate
correctly, have your power tool serviced by a qualified
repair agent. Call Black & Decker customer services for
you nearest service agent.
Residual risks
The following risks are inherent to the use of saws:
Injuries caused by touching the rotating parts.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided, these are:
Impairment of hearing.
Risk of accidents caused by the uncovered parts of the
rotating saw blade.
Risk of injury when changing the blade.
Risk of squeezing fingers when opening the guards.
Health hazards caused by breathing dust developed
when sawing wood, especially oak, beech and MDF.
Additional safety instructions for lasers
This laser complies with class 1M according to IEC
60825-1:2007. Do not replace a laser diode with a different
type. If the laser is damaged, have the laser repaired by an
authorised repair agent. Do not use the laser for any purpose
other than projecting laser lines.
Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
Do not set up the tool where the laser beam can cross
any person at head height.
Do not let children come near the laser.
Warning! Avoid direct eye contact. Laser radiated when
laser guide is turned on. Avoid direct eye contact. Always un-
plug the mitre saw from power source before making any
adjustment.
A laser pointer is not a toy and should not come into
hands of children. Misuse of this appliance can lead to
irreparable eye injuries.
Any adjustment to increase the laser power is forbidden.
Any liability for damages as a result of not following
these safety instructions will be rejected.
When using the laser pointer, do not point the laser
beam towards people and/or reflecting surfaces. Even a
laser beam of lower intensity may cause eye damage.
Therefore, do not look directly into the laser beam.
The laser pointer includes no servicing components. Do
not open the housing otherwise the guarantee is void.
Safety of others
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 61029 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
ENGLISH
9