Additional Instructions - Makita LS003G Manual De Instrucciones

Ocultar thumbs Ver también para LS003G:

Manual de instrucciones (272 páginas)

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

Contenido

141

Tabla de contenido

Idiomas disponibles

Never cross your hand over the intended line

of cutting either in front or behind the saw

blade. Supporting the workpiece "cross handed"

i.e. holding the workpiece to the right of the saw

blade with your left hand or vice versa is very

dangerous.

Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proxim-

ity of the spinning saw blade to your hand may not

be obvious and you may be seriously injured.

Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence.

Always make certain that there is no gap

between the workpiece, fence and table along

the line of the cut. Bent or warped workpieces

can twist or shift and may cause binding on the

spinning saw blade while cutting. There should be

no nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece. Small debris or loose pieces of wood or

other objects that contact the revolving blade can

be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

10. Ensure the mitre saw is mounted or placed on

a level, firm work surface before use. A level

and firm work surface reduces the risk of the mitre

saw becoming unstable.

Plan your work. Every time you change the

11.

bevel or mitre angle setting, make sure the

adjustable fence is set correctly to support the

workpiece and will not interfere with the blade

or the guarding system. Without turning the tool

"ON" and with no workpiece on the table, move

the saw blade through a complete simulated cut to

assure there will be no interference or danger of

cutting the fence.

12. Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip

if not securely supported. If the cut-off piece or

workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

13. Do not use another person as a substitute for

a table extension or as additional support.

Unstable support for the workpiece can cause the

blade to bind or the workpiece to shift during the

cutting operation pulling you and the helper into

the spinning blade.

14. The cut-off piece must not be jammed or

pressed by any means against the spinning

saw blade. If confined, i.e. using length stops, the

cut-off piece could get wedged against the blade

and thrown violently.

15. Always use a clamp or a fixture designed to

properly support round material such as rods

or tubing. Rods have a tendency to roll while

being cut, causing the blade to "bite" and pull the

work with your hand into the blade.

16. Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the

workpiece being thrown.

17. If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving

parts to stop and disconnect the plug from

the power source and/or remove the battery

pack. Then work to free the jammed material.

Continued sawing with a jammed workpiece could

cause loss of control or damage to the mitre saw.

18. After finishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

19. Hold the handle firmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down posi-

tion. The braking action of the saw may cause

the saw head to be suddenly pulled downward,

causing a risk of injury.

20. Only use the saw blade with the diameter that

is marked on the tool or specified in the man-

ual. Use of an incorrectly sized blade may affect

the proper guarding of the blade or guard opera-

tion which could result in serious personal injury.

21. Only use the saw blades that are marked with

a speed equal or higher than the speed marked

on the tool.

22. Always select the correct saw blade for the

material to be cut. Do not use the saw blade to

cut materials other than those specified.

23. The saw can cut wood, aluminum or similar

materials, when using a saw blade appropriate

for the material. Do not use the saw to cut the

other material, including magnesium, steel and

iron.