Attaching The Grinding Disc - Metabo W 9-115 Instrucciones De Manejo

en ENGLISH
............ alternating current /direct current
n ............. rated speed
The "C" and "US" indicators adjacent to the
CSA Mark signify that the product has been
evaluated to the applicable CSA and ANSI/
UL Standards, for use in Canada and the U.S.,
respectively.
4. Overview
See page 2.
1 "Quick"clamping nut *
2 Support flange
3 Spindle
4 Spindle locking button
5 Sliding on/off switch *
6 Handle
7 Electronic signal indicator *
8 Thumbwheel for selection of speed *
9 Trigger switch *
10 Switch-on lock
11 Additional handle/Additional handle with vibration
damping *
12 Safety cover
13 2-hole nut *
14 2-hole spanner *
15 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
5. Commissioning
Before plugging in, check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match with your power supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
5.1 Attaching the additional handle
Always work with the additional handle
attached! (11) Attach the additional handle on
the left or right of the machine and secure.
5.2 Attach the safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter10.Accessories!
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See illustration C on page 2.
- Push and hold the lever. (15) Place the safety
guard in the position indicated. (12)
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the safety guard.
12
(Disassemble in reverse order.)

6. Attaching the grinding disc

Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the cutting guard
before performing cutting-off operations (see
chapter 10. Accessories).
6.1 Locking the spindle
- Press in the spindle locking button and turn the
spindle by hand until the spindle locking button
engages. (4) (3)
6.2 Placing the grinding wheel in position
See illustration A on page 2.
- Fit the support flange on the spindle. (2) The
flange should not turn on the spindle when
properly attached.
- Place the grinding disc on the support flange. (2)
The grinding disc must lay flat on the supporting
flange.
6.3 Securing/Releasing the "Quick"
clamping nut (depending on features)
Securing the (1)"Quick" clamping nut:
Only attach the "Quick" clamping nut (1) to
tools with "Metabo Quick System". These
tools can be identified by the red spindle lock button
(4) with "M-Quick" logo
Do not use the "Quick" clamping nut if the
accessory has a clamping shank thicker than
7.1 mm! In this case, use the 2-hole nut (13) with 2-
hole spanner (14).
- Lock the spindle (see chapter 6.1).
- Position the "Quick" clamping nut on the spindle
so that the 2 lugs engage in the 2 grooves on the
spindle. (1) (3) See illustration on page 2.
- Tighten the "Quick"clamping nut by turning
clockwise by hand.
- Turn the grinding wheel firmly clockwise to tighten
the "Quick"clamping nut.
Releasing the clamping nut (1):
Only when the "Quick" clamping nut (1) is
attached must the spindle be stopped using
the red M-Quick spindle locking button! (4)
- The machine continues to run after switching off.
- Press in the M-Quick spindle locking button just
before the grinding disc stops. (4) The "Quick"
clamping nut (1)loosens itself by around half a turn
and can be removed without additional effort or
tools.
Use only accessories that
are covered by at least 3.4
mm by the safety guard.