Idiomas disponibles
Idiomas disponibles
Rapid switch off:
1. on pressing the keys "+" and "-" (5 and 4)
simultaneously, the timer is deactivated.
Pause mode
Activating the Pause function:
While at least one cooking zone is working, the cooking
zones can be switched off by touching the "Pause" key for
more than 1 sec
During the pause:
Timers already programmed are discontinued and remain in
this condition during the puse.
The pause mode can last for max. 10 min. If the status is not
cancelled within this period, the control unit switches off.
The cooking zone can be switched off via the ON/OFF key
any time, a possible break mode is, thus, aborted.
Terminating the Break mode:
Touching Pause key together with any other one key within
10 sec causes a re-establishment of the state prevailing prior
to the break mode.
If no further key is touched within 10 sec, the cooking zone
also switches off.
Precautions (Fig. 3)
- When one makes use of heating elements, we advise
receptacles with flat bottom having same diameter or lightly
higher than that of the hot area.
- Avoid overflows of liquid, therefore when boiling has
happened, or in any case when liquid is heated, reduce the
heat supply.
- Don't leave the heating elements on without receptacles on
the top or with void pots and pans.
- If the surface of the hob is damaged, immediately
disconnect the appliance from the mains to prevent the
possibility of electric shock.
- Never use a steam cleaner to clean the hob.
- This appliance is not designed to be used by people
(including children) with reduced physical, sensorial or
mental capacity, or who lack experience or knowledge about
it, unless they have had supervision or instructions on how
to use the appliance by someone who is responsible for their
safety.
- Children must be supervised to ensure that they do not
play with the appliance.
Maintenance (Fig. 4)
By means of a scraper immediately remove any alluminium
foil bits, food spills, grease splashes, sugar marks and other
high sugarcontent food from the surface in order to avoid
damaging the hob.
Subsequently clean the surface with some towel and
appropriate product, rinse with water and dry by means of a
clean cloth. Under no circumstance should sponges or
abrasive cloths be used; also avoid using aggressive
chemical detergents such as oven sprays and spot
removers.
Installer's Instructions
Installation
These Instructions are for the qualified technician, as a guide
to installation, adjustment and maintenance, according to
the laws and standards in force. These operations must
always be carried out when the appliance has been
disconnected from the electric system.
Positioning (Fig. 5)
1 Front view
2 Front side
The appliance can be fitted into a working area as illustrated
on the figure. Apply the seal supplied over the whole
perimeter of the working area.
Electrical connection
Prior to carrying out the electrical connection, please ensure
that:
the plant charac- teristics are such as to follow what is
indicated on the matrix plate placed at the bottom of the
working area;
-
that the plant is fitted with an efficient earth
connection, following the standards and law
provisions in force.
-
The earth connection is compulsory in terms of
the law.
Should there be no cable and/or plug on the equipment, use
suitable absorption material for the working temperature as
well, as indicated on the matrix plate. Under no
circumstance must the cable reach a temperature above
50°C of the ambient temperature.
Should a direct connection to the network be required, it will
be necessary to interpose an omnipolar switch with min.
aperture between the 3 mm. contacts, dimensioned to bear
the plate load and it must follow the standards in force (the
yellow/green earth cable must not be interrupted by the
switch). The plug or omnipolar switch must be easily
reached on the installed equipment.
The manufacturers decline any responsibility in the event of
non-compliance with what is described above and the
accident prevention norms not being respected and
followed.
To avoid all risk, if the power cable becomes damaged, it
must only be replaced by the manufacturer, by an
authorised service centre, or by a qualified electrician.
