Idiomas disponibles
Idiomas disponibles
THIS APPLIANCE IS CONCEIVED FOR DOMESTIC USE
ONLY. THE MANUFACTURER SHALL NOT IN ANY WAY BE
HELD RESPONSIBLE FOR WHATEVER INJURIES OR
DAMAGES ARE CAUSED BY INCORRECT INSTALLATION OR
BY UNSUITABLE, WRONG OR ABSURD USE.
The manufacturer declares that this product meets all the
essential requirements for low voltage electrical material set
out in European directive 2006/95/EEC of 12 December 2006
and for electromagnetic compatibility as required by
European directive 2004/108/EEC of 15 December 2004.
User's Instructions
Installation
All operations relative to installation (electric connection)
should be carried out by skilled personnel in conformity with
the rules in force.
As for the specific instructions see part pertaining to
installer.
Use
TOUCH CONTROL HEATING ELEMENTS
Touch sensitive keys
All operations can be performed using touch sensitive keys
(capacitive sensors) located on the front of the control
board; each key has a corresponding display. All actions are
confirmed by an audible signal.
TOUCH CONTROL A (Fig. 1)
1 Power ON/ Power OFF
2 cooking zone
3 setting display
4 minus
5 plus
6 dual circuit
7 timer
8 timer display
9 lock function
10 dual circuit indicator light
11 timer indicator lights
12 lock indicator light
13 decimal point
14 pause
Switching the appliance on and off Touch control
1. Touch the touch key ON/OFF for 2 seconds. The control is
powered on: the power
the decimal points (13) flash. The next operation must be
performed within 10 seconds or the appliance will
automatically switch off.
Switching on a cooking zone
After switching on the appliance by pressing (1), a cooking
zone must be switched on within 10 seconds as follows:
1. Press the key (2) corresponding to the cooking zone. The
relative display will show "0". The decimal point of display
(13) will light up, indicating that the zone is now on.
2. Set the power level (1 to 9) using the keys "+" and "-" (5/
4). The keys "+" and "-" have a repeater function, i.e. holding
level indicators (3) show "0" and
these keys pressed will increase or reduce the setting by one
unit every 0.3 seconds. Only one cooking zone may be
switched on at a time, so only one decimal point is lit up.
Switching off a cooking zone
1. The cooking zone must be on. The corresponding decimal
point (13) must be lit up.
2. Reduce the power level to "0" by pressing (4). After 3
seconds the cooking zone will switch off automatically.
Rapid switch off:
1. The cooking zone must be on and the corresponding
decimal point (13) must be lit up.
2. Press keys "+" and "-" (5/4) simultaneously and the zone
will switch off immediately.
Residual heat indicators.
While the cooking zone is still hot enough to cause burns,
the corresponding display hows the symbol "H" (residual
heat). The symbol only disappears when the temperature
falls below 60° C and there is no longer any risk of burns.
The display shows "0" as long the temperature remains
below 60°C, switching to "H" only when the temperature
rises above 60°C.
To save energy, switch off the cooking zone before cooking
is completed in order to make use of the residual heat.
The residual heat indicator "H" will go out if the power
supply is interrupted for more than 3 seconds.
Switching off the appliance
The appliance may be switched off at any time by pressing
the power key (1).
Dual circuit cooking zone.
Two cooking zones may be equipped with a dual circuit, e.g.,
a central disc and an outer ring. You can either use the
central zone alone or both zones together and thus adapt the
cooking area to suit the size of the pan.
Switching on a dual circuit zone.
1. The relative zone must be on. The decimal point (13) on
the corresponding display must be lit up.
2. Select the desired power level (1 to 9).
3. Switch on the second circuit by pressing the dual circuit
key (6).
The indicator light (10) of the selected zone will illuminate;
the second circuit is switched on together with the first.
Switching off the second circuit of a dual circuit zone.
1. The dual circuit zone must be on. The decimal point (13)
on the corresponding display must be illuminated.
2. Touch the dual circuit key (6). The indicator light (10)
goes out and the second circuit is switched off.
Appliance lock function and automatic safety switch off
Appliance lock function
The entire appliance may be locked to prevent unintentional
operation by pressing the lock key (9). This also serves a
child safety function. If the lock function is not deactivated
before the appliance is switched off, it will still be active
when the appliance is next switched on.
While the lock function is activated, operating the keys will
have no effect.
