Wearing Parts - Oase Biotec Screenmatic 12 Instrucciones De Uso

- GB -
regulations valid for installers. Ensure that the safety transformer is located at a minimum spacing from the pond edge
of 2 m (in Germany) and 2.5 m in Switzerland. Compare the electrical values of the power supply with those on the
type plate on the packaging or on the unit itself. Never operate the unit if the cable or housing are defective! Discon-
nect the power! Do not carry or pull the unit by the connection cable. Only use the unit with the attendant safety trans-
former contained in our scope of delivery. Never open the unit housing or its attendant components, unless this is
explicitly mentioned in the operating instructions. Always disconnect the power supply of all units located in water and
of this unit prior to performing work on the unit! The power cable cannot be replaced, if damaged, the entire Screen-
matic insert has to be replaced! Never carry out technical changes to the unit. Only use original spare parts and acces-
sories. Only allow authorised customer service outlets to perform repairs. Never use the system for filtering fluids other
than water! Ensure that the filter will not overflow. Danger of completely emptying the pond. For your own safety,
consult an expert when you have questions or encounter problems!
Installation (A)
Lay the outlet pipes for the water outlet into the pond and for the drain outlet into the sewage system or flower bed with
a sufficient gravity. Ensure that the unit is placed at a flood protected place and on firm ground (A1). When installing an
OASE UVC pre-clarifying unit (e.g. Bitron), place the unit at a minimum distance of 2 m from the pond edge (A1). Place
the transformer at a minimum distance of 2 m from the pond edge at a flood protected place (A1). Ensure unrestricted
access to the cover to be able to carry out work on the unit. Push (A2) or turn the hose onto the stepped hose nozzle
and secure with a hose clip. Push the flat sealing ring on the stepped hose connection, insert the stepped hose con-
nection into the inlet opening of the filter housing, and screw-tighten the water inlet socket from inside (A2). Close the
second water inlet with the closed hose nozzle (except when fitting a OASE UVC pre-clarifying unit, e.g. Bitron). Lay
the hose such that it will not deform when walked on, avoid kinks and connect it to the pump.
Start-up (B)
Switch on the pump, open the unit cover, set the water jet using regulator at the water distributor (B2) such that it hits
the first third of the screen. Close the cover, connect the motor connection cable to the transformer, connect power
plug (B1). The unit functions automatically, cleaning is every 30 minutes. Note: The Biotec filter is a biological filter
system and requires several weeks after its first installation to reach its full biological effect.
Maintenance and cleaning ( C )
Adhere to the safety information given above! Always unplug the power cables of the pump and of the Screenmatic
prior to starting work (B3)! Only clean the filter when required, do not use chemical cleaning agents to permit the filter
biology to optimally develop, knowing that cleaning agents kill the bacteria in the foam filters.
Clean and change the Screenmatic screen
Open the unit cover, remove and empty out the collection container (C1). If required, rmove the Screenmatic insert
(C2). For this purpose, tilt up the screen insert, loosen the sealing plug of the power cable from the container wall
inward, pull the power cable inward through the container wall, press in the lateral engagement hooks on the Screen-
matic insert and remove same. Press the Screenmatic unit of Biotec 36 to the rear (C2), then remove. Undo the lateral
screws (C3) from the side section without motor, remove side section, release the clamping lever (C4), and remove the
Screenmatic screen to the front. Thoroughly clean the Screenmatic screen, the strippers, and the screen from both
sides under running water. Replace the screen, if necessary. Reassemble the Screenmatic insert in the reverse order,
lead the power cable through the opening in the container wall and close the wall using the sealing plug.
Clean and replace the foam filters, clean the substrate tubes or change the substrate
Open the unit cover and tilt the screen insert upward (C5). To mechanically clean the foam filters, place the cleaning
tool on a foam holder and compress the foam inserts several times; if necessary, remove the foam filters (C6) and
rinse with clean water. Remove the separating plate between the filter and substrate chamber. Open the cleaning
outlet using the slide valve until the water has completely drained, close and switch the pump on until the filter is
completely filled with pond water. Open the cleaning outlet again and drain the water. Repeat rinsing 2 – 3 times.
Remove the substrate pipes, clean under running water, or replace the substrate. Re-insert the substrate tubes in the
guides, refit the separating plate, tilt the screen insert down again and close the filter cover, then switch the pump on
again.
Storage/Over-wintering
Put the unit out of operation at water temperatures below 8 °C or, at the latest, when freezing temperatures are to be
expected. Drain and thoroughly clean the unit, check for damage. Remove, clean, dry and store all foam inserts and
substrate tubes in a frost-free environment. Do not immerse the power plug in the water! Ensure that the storage place
is inaccessible to children. Cover the filter container such that the ingress of rain water is excluded. Drain all hoses,
pipes and connections as far as possible.

Wearing parts

Foam filters, substrate filters and the Screenmatic screen are wearing parts and are, therefore, not covered by our
warranty. Neither the transformer nor the Screenmatic drive can be repaired in the event of damage to the cables or
the housing and have to be replaced.
Disposal
Dispose of the unit in accordance with the national legal regulations. Ask your specialist dealer.
8