Power Connections; Power Source; Extension Cords - Delta 36-6023 Manual De Instrucciones

POWER SOURCE

This saw is equipped with a 15-amp motor for use with a
120-volt, 60-HZ alternating current. See instructions below
regarding proper connections for your saw as wired.
For voltage, the wiring in a shop is as important as the motor's
rating. A line intended only for lights may not be able to
properly carry the current needed for a power tool motor; wire
that is heavy enough for a short distance may be too light for
a greater distance; and a line that can support one power tool
may not be able to support two or three. A separate electrical
circuit should be used for your machines. This circuit should
not be less than #12 wire and should be protected with a
20-amp time lag fuse. If an extension cord is used, use only
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP
LOCATIONS.

EXTENSION CORDS

Never use a damaged extension cord. Check extension cords before each use. If damaged, replace immediately.
Touching the damaged area could case electrical shock resulting in serious injury.
Keep the extension cord clear of the work area. Position the cord so it will not get caught on lumber, tools or
other obstructions.
Use proper extension cords. Make sure your extension cord is a 3-wire extension cord which has a 3-prong grounding type plug
and matching receptacle which will accept the machine's plug, as described in this manual's Grounding Instructions. When using
an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in
line voltage, resulting in loss of power and overheating. The table below shows the maximum gauge to use depending on the cord
length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Only round, jacketed cords
listed by Underwriter's Laboratories (UL) should be used.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Volts Total Length of
Rating Cord in Feet
0-6 240 up to 50
0-6 240 50-100
0-6 240 100-200
0-6 240 200-300
6-10 240 up to 50
6-10 240 50-100
6-10 240 100-200
6-10 240 200-300
10-12 240 up to 50
10-12 240 50-100
10-12 240 100-200
10-12 240 200-300
12-16 240 up to 50
12-16 240 50-100

POWER CONNECTIONS

Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
3-wire extension cords which have 3-prong grounding-type
plugs and matching receptacle which will accept the machine's
plug. Before connecting the machine to the power line, make
sure the switch (s) is in the "OFF" position and be sure that
the electric current is of the same characteristics as indicated
on the machine. A substantial voltage drop will cause a loss
of power and overheat the motor. It may also damage the
machine.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Volts Total Length of
Rating Cord in Feet
0-6 120 up to 25
0-6 120 25-50
0-6 120 50-100
0-6 120 100-150
6-10 120 up to 25
6-10 120 25-50
6-10 120 50-100
6-10 120 100-150
10-12 120 up to 25
10-12 120 25-50
10-12 120 50-100
10-12 120 100-150
12-16 120 up to 25
12-16 120 25-50
12-16 120
GREATER THAN 50 FEET
8
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
NOT RECOMMENDED