Festool TDK 12 Instrucciones De Servicio/Lista De Piezas De Repuesto página 9

1.4 Wall mounting LC 45
The charger LC 45 has two longitudinal slots on
its rear by which it can be suspended on walls
using two screws (e.g. button-headed or fl at
head screw with a shaft diameter of 5 mm).
Screw both screws into the wall 96 mm apart
until the screwhead is protruding from the wall
by approx. 4 mm.
2
Machine settings
Remove the battery pack before any adjust-
ments, maintenance or repair is carried out!
2.1 Exchanging the battery pack
Removing battery pack
Press the two buttons (1.1) and slide the bat-
tery pack forwards to remove.
Inserting battery pack
Slide the battery pack into the holder on the
underside of the handle until it latches into
place (see Fig. 1).
2.2 To change the direction of rotati-
on
The selector button (1.4) determines the direc-
tion of rotation. Turn button from right to left =
clockwise rotation. Turn button from left to
right = anticlockwise rotation. Selector but-
ton in central position = circuit interlock.
2.3 Shifting speeds
Change only when completely stop-
ped!
Using the shift lever (1.5), the speed can be
changed.
1. Speed: Lever forward - Figure 1 is visible.
2. Speed: Lever backwards - Figure 2 is vi-
sible.
2.4 Torque adjustment
By turning the adjustment ring (1.6) the re-
quired torque can be adjusted. The arrow (1.7)
aligns with the adjusted state.
Drilling
Drilling symbol on adjustment ring aligns with
the arrow = maximum torque.
Screws
Torque corresponding to setting:
Position 1 = low torque
Position 20 = high torque
3 Tool holding fi xture, attachments
3.1 Chuck BF-FX
The chuck is used to clamp drills and bits.
a) Fitting/removing the chuck
Fitting
- Place the chuck on the drill spindle (2.5) and
twist until the hexagon key (2.4) of the chuck
latches into the hexagon socket of the drill
spindle.
- Pull the unlocking ring (2.3) forwards, press
the chuck onto the drill spindle up to the stop
and release the unlocking ring.
Removal
- Pull the unlocking ring forwards and remove
the chuck.
All manuals and user guides at all-guides.com
b)
- Turn the clamping sleeve (2.2) anti-clockwise
- Insert the tool into the chuck.
- Clamp the tool by turning the clamping sleeve
3.2
The angle attachment permits work (drilling,
screwing) vertical to the machine's longitudinal
axis.
a)
Fitting
- Place the angle attachment on the drill spindle
- Lock the angle attachment by turning the
Removal
- Turn the fastening ring anti-clockwise up to
b)
The chuck is fi tted on the shaft (2.6) of the
angle attachment in the same way as on the
drill spindle of the machine.
3.3
The eccentric attachment is used to hold bits.
It allows screwing close to edges.
a)
The eccentric attachment is fi tted/removed in
the same was as the angle attachment (see
Chapter 3.2).
b)
- Pull the unlocking ring (2.8) back and remove
3.4
The CENTROTEC toolholder enables rapid chan-
ges of tools with CENTROTEC shafts.
a)
Fitting
- Pull the release ring (2.11) forwards, place
Removal
- Pull the release ring forwards and take off the
9
Changing tools
to open the clamping jaws (2.1) (Note: the
spindle is automatically locked when the ma-
chine is switched off).
clockwise. Always make sure that the tool is
clamped centrally in the chuck.
Angle attachment DD-AS
Fitting/removing the angle attach-
ment
and turn until it catches in the desired position
(Note: The angle attachment can be fi tted in
16 different angle settings).
fastening ring (2.7) tightly clockwise.
the stop and remove the angel attachment.
Fitting/removal of chuck on angle
attachment
Eccentric attachment DD-ES
Fitting/removing the eccentric at-
tachment
Changing tools
the tool and/or insert the new tool.
CENTROTEC WH-CE toolholder
Do not fi t CENTROTEC tools at the round
shaft section in a conventional chuck to
prevent damage to the shaft.
Danger of injury! When changing
tools, handle the tool and its sharp
cutters with special care and wear pro-
tective gloves, if necessary.
Fitting/removing CENTROTEC
the toolholder as far as it will go on the drill
spindle (2.5) and let go of the release ring.
toolholder.