Water Filtration System; Ice Maker And Storage Bin - KENMORE ELITE 106.5116 Serie Manual De Uso Y Cuidado

Press ACCENT LIGHT a second time to turn the dispenser
pad light off.
The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see "Problem
Solver" for more information.
The Dispenser Lock
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the
refrigerator, to the ice maker, or to the dispenser light. It simply
deactivates the controls and dispenser pad. To turn off the ice
maker, see "Ice Maker and Storage Bin."
Press and hold LOCK for 3 seconds to lock the dispenser.
Press and hold LOCK a second time to unlock the dispenser.
The display screen indicates when the dispenser is locked.

Water Filtration System

Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Water Filter Status Light
The water filter status light will help you know when to change
your water filter.
When the dispenser control panel's water filter status
display changes to "ORDER," this tells you that it is almost
time to change the water filter cartridge.
Replace the water filter cartridge when the water filter
status display changes to "REPLACE."
NOTE: If water flow to your water dispenser or ice maker
decreases noticeably, change the filter sooner. The filter
should be replaced at least every 6 months, depending on
your water quality and usage.
Resetting the Filter Status
After changing the water filter, reset the status light. Press
the SETTINGS button, then press SETTINGS to initiate the
reset, then press MEASURED FILL to confirm that you want to
reset the status light.
When the system is reset, the "ORDER" and "REPLACE"
icons will disappear from the display screen.
All manuals and user guides at all-guides.com
NOTE: When the status displays "REPLACE," you can
temporarily reset the status icon manually, without changing the
water filter. Press and hold the ACCENT LIGHT and
TEMPERATURE buttons at the same time for 3 seconds. The
"REPLACE" display will be turned off for 14 days. When it turns
back on, you can manually reset it again if desired.
Changing the Water Filter
1. Locate the water filter in the top-right corner of the
refrigerator compartment.
2. Lift open the filter cover door. The filter will be released and
then be ejected as the door is opened.
3. When the door is completely open, pull the filter straight
out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
4. Take the new filter out of its packaging and remove the
covers from the O-rings. Be sure the O-rings are still in place
after the covers are removed.
5. With the arrow pointing up, align the new filter with the
filter housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the
filter into place. You may need to press hard.
7. Flush the water system. See "Water and Ice Dispensers."

Ice Maker and Storage Bin

(on some models)
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply
cannot be avoided, make sure the water softener is
operating properly and is well maintained.
Do not use anything sharp to break up the ice in the storage
bin. This can cause damage to the ice container and the
dispenser mechanism.
Do not store anything on top of or in the ice maker or
storage bin.
21