Stanley FATMAX SFMCS310 Traducido De Las Instrucciones Originales página 9

To lock the tool, slide the speed selector to the locked
u
position. When the lock/speed change lever is in the
locked position, the tool is locked and the trigger switch
cannot be pulled.
Switching on and off
The variable speed on/off switch offers a choice of speeds for
greatly improved cutting rates in various materials.
To switch the tool on, squeeze the variable speed on/off
u
switch (5).
To switch the tool off, release the variable speed on/off
u
switch (5).
Correct hand position (Fig. G)
Warning! To reduce the risk of serious personal injury,
ALWAYS use correct hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Correct hand position requires one hand on the hand grip (9) ,
with the other hand on the main handle (8) .
Sawing
Always hold the tool with both hands.
u
Let the blade run freely for a few seconds before starting
u
the cut.
Apply only a gentle pressure to the tool while performing
u
the cut.
If possible, work with the shoe (5) pressed against the
u
workpiece. This will improve tool control and reduce tool
vibration, as well as prevent the blade from being
damaged.
Hints for optimum use
Sawing wood
When cutting wood, use speed 2 to maximize performance.
Clamp the workpiece securely and remove all nails and
u
metal objects.
Holding the tool with both hands, work with the shoe (5)
u
pressed against the workpiece.
Flush cutting
The compact design of the reciprocating saw motor housing
and pivoting shoe permit close cutting to floors, corners and
other difficult areas.
To maximize flush cutting capabilities:
Insert the blade shaft into the blade clamp with the teeth of
u
the blade facing up.
Adjust the angle of the handle on the tool so you are as
u
close to the work surface as possible.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
(Original instructions)
When cutting metal, use speed 1 to maximize blade life.
Use a saw blade suitable for sawing metal. Use a
u
fine-tooth saw blade for ferrous metals and a coarser saw
blade for non-ferrous metals.
When cutting thin sheet metal, clamp a piece of scrap
u
wood to the back surface of the workpiece and cut through
this sandwich.
Spread a film of oil along the intended line of cut.
u
Pocket cutting in wood
Measure and mark the required pocket cut.
u
Fit a saw blade suitable for pocket cutting.
u
Rest the shoe (5) on the workpiece in such a position that
u
the blade forms an appropriate angle for the pocket cut.
Switch on the tool and slowly feed the blade into the
u
workpiece. Make sure that the shoe (5) remains in contact
with the workpiece at all times.
Cutting branches
Branches up to 25 mm in diameter can be cut with this tool.
Warning! Do not use the tool while in a tree, on a ladder or on
any other unstable surface. Be aware of where the branch will
fall.
Cut downward and away from your body.
u
Make the cut close to the main branch or tree body.
u
Vertical cutting
The tool allows close cutting to corners and other difficult
areas.
Insert the shank of the saw blade into the blade holder
u
with the teeth of the blade facing upward.
Hold the tool with the shoe (5) facing downward so that
u
you are as close to the work surface as possible.
Cut forward and away from your body.
u
LED worklight
The worklight (11) is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
Note: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Accessories
The performance of your tool depends on the accessory used.
STANLEY FATMAX accessories are engineered to high
quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
Warning! Since accessories, other than those offered by
STANLEY FATMAX, have not been tested with this product,
use of such accessories with this tool could be hazardous.
ENGLISH
9