Technical Data; Drill Safety Warnings; English - Milwaukee DD 3-152 Manual Original

TECHNICAL DATA

Diamond Drill
Production code
Rated input
No-load speed 1st gear
No-load speed 2nd gear
No-load speed 3rd gear
Drilling using the drill stand:
Drilling capacity max. in concrete, 1st/2nd/3rd gear
Hand-held drilling:
Drilling capacity max.
in concrete, 2nd/3rd gear
in brick and tile, 1st/2nd/3rd gear
Tool reception
Weight according EPTA-Procedure 01/2014
Weight + DR 152 T
GB
Safety class
Degree of protection
Noise information
Measured values determined according to EN 62841-2-1. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841-2-1
Drilling into concrete, wet
Vibration emission value a
Uncertainty K=
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for di erent
applications, with di erent accessories or poorly maintained, the vibration and noise emission may di er. This may signi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched o or when
it is running but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings and all instruc-
tions. Failure to follow all instructions listed below may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

a) Wear hearing protection when diamond drilling. Exposu-
re to noise can cause hearing loss.
b) Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
c) Brace the tool properly before use. This tool produces a
high output torque and without properly bracing the tool during
operation, loss of control may occur resulting in personal injury.

English

12
h,DD
DD 3-152
(110-120 V)
4315 31 04...
... 000001-999999
1700 W
0 -1000 min
0 -2100 min
0 -3900 min
152/62/32 mm
62/32 mm
200/112/62 mm
/ " / 1
1
2
6,5 kg
16,5 kg
II
IP 20
83,0 dB (A)
94,0 dB (A)
7,3 m/s
4,79 m/s
d) Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory contac-
ting a "live" wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Safety instructions when using long drill bits
a) Never operate at higher speed than the maximum speed
rating of the drill bit. At higher speeds, the bit is likely to bend
if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
b) Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is likely to
DD 3-152
(220-240 V)
4280 01 04...
... 000001-999999
1900 W
0 -1050 min
-1 -1
0 -2400 min
-1 -1
0 -4700 min
-1 -1
152/62/32 mm
62/32 mm
200/112/62 mm
/ " UNC / " / 1 / " UNC
1 1 1
4 2 4
6,5 kg
16,5 kg
II
IP 20
83,0 dB (A)
94,0 dB (A)
7,3 m/s
2 2
4,79 m/s
2 2