Intended Use - Stanley STEL365 Manual De Instrucciones

c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
FEATURES (FIG. A)
1. Trigger Switch
2. Main Handle
3. Secondary Gripping Handle
4. Adjustable Shoe Screws
5. Adjustable Shoe
6. Blade Clamp

INTENDED USE

Your Stanley hand-held saw has been designed for sawing
wood, plastics and sheet metal.
GENERAL SAFETY RULES
Warning! Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all of
the warnings listed below refers to your mains operated
(corded) power tool or battery operated (cordless) power
tool.
ADDITIONAL POWER TOOL SAFETY WARNINGS
Warning! Additional safety warnings for hand-held
saws.
f Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
f Use clamps or another practical way to secure
and support the work piece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f Hold saw firmly with both hands for all cutting
operations.During cutting operations, the blade
may suddenly bind in the work and may cause the saw
to kickback towards the operator.
f Keep hands away from cutting area. Never reach
underneath the material for any reason. Hold front
of saw by grasping the contoured gripping area.
Do not insert fingers or thumb into the vicinity of the
reciprocating blade and blade clamp. Do not stabilize
the saw by gripping the shoe.
f Keep blades sharp. Dull blades may cause the saw
to swerve or stall under pressure.
Construction
f Use extra caution when cutting overhead and pay
Earthing
particular attention to overhead wires, gas or water
Terminal
lines, which may be hidden from view. Anticipate the
Safety Alert
Symbol
path of falling branches and debris ahead of time.
Revolutions
f When cutting pipe or conduit ensure that they are
or Recipro-
cation per
free from water, electrical wiring, etc.
minute
f Do not touch the work piece or the blade
immediately after operating the tool. They can
become very hot.
ENGLISH • 9