Protecting The Environment - Stanley BC209 Manual De Instrucciones

4. When the charger is properly connected, the charging process will start automatically
for few seconds. The Charging leD (
charging.
Notes:
If the battery clamps are connected incorrectly with regard to polarity, the Reverse Polarity
leD ( ) will light red. Disconnect the charger's ac plug from the ac mains socket; then
disconnect the clamps. Reconnect the clamps with correct polarity and plug the charger back
in at the ac mains socket.
If the charging leD did not come on, check the connection to the battery. If the battery
connection is properly checked, the battery may be in fault condition. Manufacturer suggests
to have the battery tested by a qualified battery service technician.
5. Monitor the battery from time to time.
6. When the battery is completely charged, the charged leD (
When disconnecting the charger, do so in the following order: Disconnect the ac mains
plug from the ac mains socket, then disconnect the battery clamps from the battery
terminal.
charging the battery using the vehicle
adaptor plug
WARNING: NEVER connect this unit to a positive grounded vehicle by the vehicle
adapter plug.
Always follow the steps outlined in the "Safety Instructions" section at the
front of this manual.
1. Slide the battery voltage selector switch to the 6V or 12V position as required.
2. Connect the vehicle adaptor plug to the battery charger with the double-barrel in-line
connector. Insert the plug into the 12 V dc accessory outlet of the vehicle.
3. Insert the ac plug of the battery charger into an ac mains socket. The Power leD ( )
will light red to indicate the unit is plugged into a live ac mains socket.
Notes:
If the Power leD did not come on, check connection with the ac mains socket. Make sure
the ac mains socket is functional.
4. When the charger is properly connected, the charging process will start automatically
for few seconds. The Charging leD (
charging.
Notes:
Some vehicles require that the ignition be switched to the accessory outlet position in order
to power the accessory outlet.
If the charging leD did not come on, check the connection to the 12 V dc accessory outlet
of the vehicle. Rotate the plug slightly to make sure there is good contact. If the connection
is properly checked, the battery may be in fault condition. Manufacturer suggests to have the
battery tested by a qualified battery service technician.
ENGLISH
BC209EU_Manual_040512.indd 10-11
) will light red, indicating that the battery is
) will light green.
) will light red, indicating that the battery is
10
5. When the battery is completely charged, the charged leD (
When disconnecting the charger, do so in the following order: Disconnect the ac mains
plug from the ac mains socket, then disconnect the vehicle adaptor plug from the 12 V dc
accessory outlet of the vehicle.
troubleshootIng
If the appliance is not charging:
• Check that the correct voltage has been selected for the battery being charged.
• Make sure the output connections are secured and the polarity connection is correct.
• Check that the battery charger is properly connected to a live 230 V ac socket (the power
leD ( ) will light red).
• If the voltage of the battery to be charged has fallen below 2 volts, the battery cannot be
charged with this battery charger.
care and MaIntenance
From time to time wipe the appliance with a damp cloth. Do not use any abrasive or
solvent-based cleaner. Do not immerse the appliance in water.
WARNING: Before performing any maintenance or cleaning on the appliance, unplug
the appliance.
fuse replacement (12 volt dc charging adapter)
1. Remove plug from accessory outlet. Remove the gold cap by turning counter clockwise
and lifting off.
2. Remove center pin and spring. Remove fuse.
3. Replace fuse with same type and size fuse (5 amp).
4. Replace center pin and spring inside plug.
5. Replace gold cap by turning clockwise.

ProtectIng the envIronMent

correct disposal of this product
This marking indicates that this product should not be disposed with other household
wastes throughout the eU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
) will light green.
11 11 DEUTSCHn ENGLISHn
4/5/2012 6:45:01 PM