Setting The Temperature Limiter - Grohe Europlus E 36 015 Manual De Instrucciones

Operation
The infrared-electronic system emits invisible, pulsed light.
The infrared-electronic is adjusted so that water flow is
initiated when the hands approach the vicinity of the spout.
When the hands are withdrawn from the vicinity of the spout,
water flow is stopped after 1 s (factory setting).
The range of the sensor system is dependent upon the
reflective properties of the detected object.
Note:
For anonymous use, we recommend affixing the enclosed
sticker.
36 015, 36 017

Setting the temperature limiter

1. Remove screw (E) using a 2mm allen key, see Fig. [6].
2. Turn mixer lever (F) clockwise until the desired maximum
temperature is reached.
3. Detach mixer lever (F), see Fig. [7].
4. Detach stop ring (G) and reattach with notch (G1) pointing
vertically upwards.
5. Turn mixer spindle (H) anti-clockwise to the stop.
6. Attach mixer lever (F) in horizontal position and fasten with
screw (E).
Cleaning
• For cleaning purposes, the fitting can be switched off by
attaching the enclosed cleaning clip (J), see Fig. [8].
The fitting can be switched off using the remote control (see
Special accessory, Prod. no.: 36 206).
Automatic safety shut-off
After 60 s (factory setting) of continuous detection of an object,
the infrared electronics automatically stop the water flow.
The automatic safety shut-off can be set in steps of 5 - 420 s
using the remote control (see Special accessory, Prod.
no.: 36 206).
Automatic flushing
(factory setting: not activated)
The automatic flushing serves to maintain water hygiene in the
case of long-term non-utilisation of the fitting and activates
water flow for 1 – 10 minutes, 1 or 3 days after the last use.
Safety notes:
- Ensure free draining in the case of activated automatic
flushing.
- For automatic flushing of the hot and cold water lines, the
fitting must be in the mixed water setting.
Automatic flushing can be switched off using the remote
control (see Special accessory, Prod. no.: 36 206) as follows:
5
1. Switching automatic flushing On / Off.
• Press and hold the RESET button.
• Then additionally press OFF AUTO button within 2 s.
(warning lamp in fitting flashes).
- Switching on: Within 10 s, press OFF AUTO button
Warning lamp in sensor system flashes 4 x short = On
- Switching off: Within 10 s, press OFF AUTO button
Warning lamp in sensor system flashes 2 x long = Off
Setting mode is quit automatically after 10 s.
2. Changing flushing interval from 3 to 1 day
(factory setting: 3 days).
• Press TEST button => test mode is switched on
The flushing interval can be set via the ON AUTO button.
• Press the ON AUTO button.
Warning lamp in sensor system flashes:
- 2 x long = 1 day
- 4 x short = 3 days
Setting mode is quit by pressing the TEST button, or
automatically after 60 sec.
3. Setting flushing duration from 1 to 10 minutes (factory
setting: 5 minutes).
• Press TEST button => test mode is switched on
Using the + and - buttons (
duration can be increased (+) or reduced (-).
• Press the + or - button (
Warning lamp in sensor system flashes:
- 4 x short = adjustment by one step (approx. 1 minute)
- 2 x long = end position reached
Setting mode is quit by pressing the TEST button, or
automatically after 60 sec.
Setting continuous running time to 3.5 min or 11 min
(factory setting: 3.5 min)
• Press TEST button => test mode is switched on
The continuous running time can be set using the OFF
AUTO button.
• Press the OFF AUTO button as required.
The warning lamp in the sensor system of the fitting flashes:
- 2 x long = 11 min continuous running is set
- 4 x short = 3.5 min continuous running is set
Setting mode is quit by pressing the TEST button, or
automatically after 60 sec.
Maintenance
Inspect and clean all components and replace if necessary.
Shut off the hot and cold water supplies and switch off the
voltage supply.
I. Transformer
1. Interrupt the voltage supply via transformer (D), see Fig. [9]
2. Detach plug-in connector (C).
Assemble in reverse order.
button), the flushing
button).