Thuasne Sleeq Flex Manual De Instrucciones página 5

Sleeq Flex (54 660)
Spinal orthosis for active relief and
correction of the lumbar and the thoracic spine
in the sagittal plane
Purpose
The Sleeq Flex spinal orthosis is an orthosis for active
relief and correction of the lumbar and the thoracic spine
in the sagittal plane. The orthosis may only be used for
lower spine treatment.
Properties
• Pulley system for individual power transmission
• Pliable material
• Reinforcing elements in the abdominal area
Indications
• Stable, osteoporotic vertebral fractures
• Hunchback with poor shoulder posture
• Spondylitis
• Morbus Bechterew
Contraindications
• Unstable vertebral fractures
• Do not apply the product near open wounds
• Haematomas and severe swelling
Side effects
When properly applied, no side effects have been known
to date.
Putting on the orthosis
Size determination and adjustment
The Sleeq Flex spinal orthosis has a universal size and can
be individually adjusted to the circumferences.
(Fig . 1) Four size markings (1, 2, 3, 4) show markings for
the waist size and the correct alignment. They are merely
used for orientation since the size can be varied at will and
individually adjusted.
(Fig. 2) Loosen the tension straps and place them on the
spinal pad, with the hook-and-loop fastening facing up.
Now push the right wing to the inside or the outside and
firmly press the crescent-shaped hook-and-loop fastening
on the suitable size marking (or between the markings).
Repeat this setting with the left wing as well. Make sure
that the hook-and-loop fastening fits firmly between the
waist strap and the crescent-shaped hook-and-loop part. If
the desired setting does not fit, repeat it until the circum-
ference is correct.
(Fig. 3) If necessary, the waist strap may be fixed slightly
diagonally upwards or downwards to thus obtain a better
waist adjustment.
In order to relieve the pulley system, leave the tension
straps still on the spinal pad and simultaneously pull on
the left and right waist strap. Once you feel any resistance,
the system will be adjusted and both waist straps should
now have the same length. You can now firmly fasten, by
hook and loop, the tension straps on the left and right each
(without pull) on the waist strap.
Putting on the orthosis
(Fig. 4) Loosen the shoulder straps and push the arms
through the straps (for larger patients, the „ThoraCare"
carrier may be pushed upwards before putting it on). Now
centre the spinal pad at the desired height in the lumbar
region and then close the ventral wings (without pull). To
this end, place the left strap on the abdomen and use the
hook-and-loop system to fasten the right strap on the left.
GB USA
(Fig. 5a) For the individual pressure setting, please loosen
the tension straps on the outside. Then put your thumbs
into the opening and pull the straps forward to the outside
until you feel a comfortable and firming pressure. In order
to fix the two strap ends, simply use the hook-and-loop
system to fasten the flaps again on the waist strap. In or-
der to firm up the shoulder straps, simply pull the traction
ropes downwards (backpack system) until they rest com-
fortably against the shoulders.
(Fig. 5b) In order to adjust the rear lengths, push the
„ThoraCare" carrier upward or downward in the pocket so
that the upper centre of the carrier is on a level with T3.
Precautions
Follow the advice of the professional who prescribed or
supplied the product. Consult your professional if discom-
fort occurs. Store at room temperature, preferably in its
original packaging. For hygiene and performance reasons,
do not re-use the product for another patient. Any serious
incident that occurs in connection with the product must
be reported to the manufacturer and to the competent
authority of the Member State in which the user and/or
patient are/is domiciled.
Care
Do not use any cleaning agents, conditioners or aggressive
products (containing chlorine).
Squeeze out the water thoroughly
Dry away from any heat sources
Material composition
Nylon, polyester, polypropylene, synthetic rubber (latex-
free)