Sammic S-41 Manual Del Usuario página 8

leaving the filters in place.
· Press the drain key (Fig. A-5) as specified
on the control panel, with the door open. The
drain pump operates during the programmed
time at the end of which it stops automatically.
By pressing the key, you can successively
start and stop the pump.
· Put the overflow drain plug and filters in place
again.
· Turn the main switch off and close the door.
Water softener. Setting water hardness. You
need to set the water hardness value on the
electronic board. The machine sig- nals that resin
regeneration is needed by means of a flashing
"Regenerate" LED (Fig. A-k). This warning signal
depends on the number of rinsing cycles done
and the selected water hardness. Therefore:
1. With the machine on and idle and both
"Disconnect Resistors" microswitches (Fig. B-1)
set to OFF, press the button (Fig. B-2) on the
electronic board.
2. One of the three "Cycle time" LEDs (Fig. A - d,
e or f) will turn on:
· Short cycle" LED (Fig. A-d) on: Low water
hardness. "Regeneration" signal every 50
rinsing cycles glasswashers and 90 rin- sing
cycles dishwashers.
· "Medium cycle" LED (Fig. A-e) on: Middle water hardness. "Regeneration" signal
every 30 rinsing cycles glasswashers and 70
rinsing cycles dishwashers.
· "Long cycle" LED (Fig. A-f) on: High water
hardness. "Regeneration" signal every 15
rinsing cycles glasswashers and 50 rinsing
cycles dishwashers.
3. Press "Start cycle" (Fig. A-4) and "Drain" (Fig.
A-5) - the LEDs will turn on successively -
until you have the required water hardness
selected.
4. Press "Select cycle" (Fig. A-3) to save the
water hardness value. The LED flashes to
confirm correct saving.
5. Switch machine off.
Water softener. Regeneration Cycle.
The machine signals that resin regeneration is
needed by means of a flashing "Regenerate"
LED (Fig. A-k). If you think it proper, you can
perform a regeneration cycle before the machi-
ne warns you to do so. In this event, do as
follows:
1. Drain the wash tank completely. MACHINE
EMPTY WITHOUT DRAIN PLUG.
2. With the door open, press "Select Cycle" (Fig.
A-3), the "Regeneration" LED (Fig. A-k) turns
on, meaning the machine is ready for the water
softener regeneration cycle.
3. Close the door and press "Start cycle" (Fig.
A-4) to start the regeneration cycle.
4. The display shows the number of rinsing
EN
8
cycles done and letters "rn" (flashing). The
regeneration cycle starts after 6 seconds.
During those 6 seconds, you can stop the
cycle by pressing "Start cycle" (Fig. A-4)
again.
5. This cycle lasts 23 minutes and cannot be
stopped. The display shows "rd" and the time
remaining to end the cycle alternatively. If
you switch the machine off during this cycle,
then on switching it on again, the display will
warn you to do a new regeneration cycle.
6. When the displays shows only "rd", the rege-
neration cycle has finished.
7. Switch the machine off to quit the regenera-
tion cycle mode.
Water softener. Refilling regenerating salt
The regenerating salt container is accessible
through the inside of the wash tank. To refill
the salt container:
1. Drain the wash tank completely.
2. Check to see if there is any salt (800g) left in
the container. Add kitchen salt as and when
necessary to fill the container. A full container
permits up to 2-3 regeneration cycles.
Tank cleaning
The tank should be cleaned after every washing
process, at the end of the day, proceeding as follows:
· Remove the bayonnet safety filter from the
wash pump (L) by twisting it counterclockwise.
· On models "B" with a drain pump, also remove
the screw-on drain pump filter (J) and clean it.
Give the filter (J) a quarter turn to undo the filter
(J). After cleaning the filter, screw it on again.
· At the end of the day, it is advisable to drain
the dishwasher, fill it with water and have
a wash cycle done on no load, without any
racks, in order to clean the interior of the
machine.
· Finally, clean the bottom, walls and interior of
the tank.
· Spray arms must be cleaned periodically. If
rinsing is deficient, the cause may be an obs-
truction of the jets. In this event, dismount the
arms and clean the jets.
· The outside of the machine MUST NOT BE
washed under a direct water jet; instead you
can use a wet cloth and any ordinary deter-
gent.
· DO NOT USE any abrasive detergent (etchant,
concentrated lye, etc.) nor any scourer or
scraper containing normal steel that will cause
rust to develop on the machine.
Boiler Draining
1. Drain the wash tank.
2. Close the water inlet.
3. Remove the tube coming from the rinsing aid
pump from the inlet connector to the boiler
and place a container under the boiler. All
water flows out of the boiler by gravity.
Adjustment of Working Temperatures:
(Figure B Electronic Boad Diagram)
Temperatures are factory-set at:
· 55-60ºC for the wash tank
· 85-90ºC for the boiler
Setting temperatures:
Setting of wash tank temperature:
1. With the machine off, set "Disconnect
Resistors" microswitch 1 (Fig. B-1) to posi-
tion ON (1 ON, 2 OFF).
2. Switch the machine on and wait until the
display stops showing the model number
and shows a temperature.
3. Now press button (Fig. B-2) on the electronic
board until all three 'Select Cycle' LEDs (Fig.
A-d, e, f) and the 'Wash Tank" LED (Fig. A-a)
turn on simultaneously. The display shows
the preset wash tank temperature.
4. Use the pushbutton "Start Cycle" (Fig. A-4)
to increase the temperature setpoint or push
button "Drain" (Fig. A-5) to decrease it.
5. Press "Select cycle" (Fig. A-3) to save
the selected temperature. The three "cycle"
LEDs turn off and the display confirms
correct saving of the value. 6. Switch the machine off.
7. Set "Disconnect Resistors" microswitch 1
(Fig. B-1) to position OFF (1 OFF, 2 OFF).
Setting of boiler temperature
1. With the machine off, set "Disconnect
Resistors" microswitch 2 (Fig. B-1) to posi-
tion ON (1 OFF, 2 ON).
2. Switch the machine on and wait until the
display stops showing the model number
and shows a temperature.
3. Now press button (Fig. B-2) on the electronic
board until all three 'Select Cycle' LEDs (Fig.
A-d, e, f) and the 'Boiler" LED (Fig. A-b) turn
on simultaneously. The display shows the
preset boiler temperature.
4. Use the pushbutton "Start Cycle" (Fig. A-4)
to increase the temperature setpoint or push
button "Drain" (Fig. A-5) to decrease it.
5. Press "Select cycle" (Fig. A-3) to save
the selected temperature. The three "cycle"
LEDs turn off and the display confirms
correct saving of the value.
6. Switch the machine off.
7. Set "Disconnect Resistors" microswitch 2
(Fig. B-1) to position OFF (1 OFF, 2 OFF).
Disconnecting the elements
The electronic board includes two "Disconnect
Resistors" microswitches (Fig. B-1) for disabling
the heating of the resistors. Therefore, setting
both microswitches to position ON disconnects