Maintenance And Cleaning - Black and Decker HVLP400 Manual De Instrucciones

Maintenance and cleaning

Your Black & Decker corded appliance has been designed to
operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper appliance care and regular cleaning.
Warning! Be sure to use appropriate personal protective
equipment.
Warning! Before performing any maintenance or cleaning on
corded appliances switch off and unplug the appliance.
Warning! Do not use materials with a flashpoint lower than
55°C. Flashpoint is the temperature that a fluid can produce
enough vapours to ignite (see paint supplier instructions).
Warning! Make sure clean up area is well ventilated and free
of flammable vapours.
Warning! Always spray outdoors when spraying cleaning
solution through sprayer.
Warning! Do not submerse power unit.
Flushing the sprayer (fig. O)
Turn the power unit off, unplug the cord and disconnect air
u
hose from sprayer.
Unscrew the lid from the side of the canister and pour any
u
remaining liquid back into the original container (fig. O).
Pour a small amount of the appropriate cleaning solution
u
into the canister.
Warm soapy water for water based materials.
t
Manufacturers recommended cleaning solution for oil
t
based materials.
Replace the lid on the canister securely and vigorously
u
shake the sprayer.
Unscrew the lid from the side of the canister and properly
u
dispose of cleaning solution.
Refill the canister with a small amount of new cleaning
u
solution. Screw lid securely on canister.
Reattach the air hose to the sprayer, plug in the cord and
u
turn on the power unit.
Spray the cleaning solution through the sprayer onto scrap
u
material for 2 to 3 seconds.
Cleaning the sprayer (fig. P - T)
Turn the power unit off, unplug the cord and disconnect air
u
hose from sprayer.
Remove the side fill canister (6) and unscrew the side lid
u
(7). Remove the pickup tube (15) and o-ring (17) from the
sprayer. Clean the parts in the appropriate cleaning solu-
tion (fig. P).
Unscrew the tip collar (19) and remove the spray nozzle
u
(10) and spray tip (20). Clean all parts in the appropriate
cleaning solution (fig. Q).
(Original instructions)
If using water based material, clean the sprayer by running
u
water through pickup tube inlet. If using oil based materi-
als, clean pickup tube inlet with the appropriate cleaning
solution. Repeat until sprayer is completely clean. Take
special care to gently clean the spraying needle (21).
Dry all parts thoroughly.
u
Properly dispose of cleaning solution.
u
Place a drop of household oil onto the metal ball in the
u
check valve (18) (fig. R).
Important : Lubricating the ball in check valve (18), after
cleanup, will help to prevent it from sticking which can clog the
valve and prevent adequate flow of spray material.
Reassemble sprayer (fig. S).
u
Note : The spray tip (20) can only go in one way. The notch
(22) on the spray tip must align with the recess in the threads
of the sprayer (fig. 3).
Cleaning the power unit
Turn the power unit off, unplug the cord and disconnect air
u
hose from sprayer.
Use only mild soap and damp cloth to clean the power
u
unit.
Warning! Never let any liquid get inside the power unit.
Warning! Never immerse any part of the power unit into a
liquid.
Cleaning the filter
The power unit contains a washable/reusable filter (fig. U).
Check the filter before and after each use. If dirty, wash with
warm water and allow to air dry before re-installing or replace
if necessary.
To check the filter, remove the filter cover (11) by pressing
u
in on the sides of the filter cover and pulling the cover off
the power unit.
Remove the filter (23) and inspect.
u
Replace the filter and filter cover.
u
Warning! Never operate the power unit without the filter in
place. Debris could be sucked in and interfere with the func-
tion of the power unit.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Connect the green/yellow lead to the earth terminal.
u
Warning! Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13A.
ENGLISH
11