Skil F0155144 Serie Manual De Instrucciones página 8

GB
INTRODUCTION
This tool is intended for lengthways and crossways
cutting of wood with straight cuts as well as angle cuts to
45°; with the appropriate saw blades also non-ferrous
metals, light building materials and plastics can be cut
TECHNICAL SPECIFICATIONS 1
SAFETY
Read and save this instruction manual (pay special
attention to the safety instructions at the back) 2
Check voltage indicated on nameplate of tool/charger/
battery
In case of electrical or mechanical malfunction,
immediately switch off the tool or unplug charger from
power source
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start cutting
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
SKIL can assure flawless functioning of the tool only
when original accessories are used
Before using accessories always compare the maximum
allowed speed of that specific accessory with the speed
of the tool
Never use the tool without the original protection guard
system
This tool should not be used by people under the age of
16 years
The noise level when working can exceed 85 dB(A);
wear ear protection
This tool is not suitable for wet cutting
The kerf guide has to be adjusted in case different
diameters of sawblade are used
Do not use a circular saw blade which is cracked,
deformed or dull
Do not use a circular saw blade of which the body
thickness is bigger, or the teeth setting is smaller than
the thickness of the kerf guide
After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
Never clamp or wedge the lower guard in open position;
ensure that it operates freely
Never use circular saw blades made of high speed steel
(HSS)
Only use thin saw blades designed for cordless circular
saws
Never use grinding/cutting discs with this tool
Do not remove the kerf guide
Keep hands away from the saw blade while the tool
is in use
Do not cut material containing asbestos
Do not attempt to cut extremely small workpieces
Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
Do not work overhead with the tool
Do not activate switch when carrying the tool
Always remove battery from tool before making any
adjustment or changing any accessory, in order to
reduce the risk of starting the tool accidentally
CHARGING/BATTERIES
Charge battery only with the charger that is supplied with
the tool
Do not charge batteries of other manufacturers
Do not touch the contacts in the charger
Do not expose tool/charger/battery to rain
Do not not carry or suspend the charger by the cord
Never charge battery outdoors 3
Store tool/charger/battery in locations where temperature
will not exceed 40° C or drop below 0°
Batteries will explode in fire, so do not burn battery for
any reason
When damaged, and under extreme usage and
temperature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, flush eyes with clean water
for a minimum of 10 minutes and seek immediately
medical attention
When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc.
to prevent short-circuit
Do not use charger when damaged; take it to one of the
officially registered SKIL Service Stations for a safety
check
Do not use charger when cord or plug is damaged; cord
or plug should be replaced immediately at one of the
officially registered SKIL Service Stations
Do not use battery when damaged; it should be replaced
immediately
Do not disassemble charger or battery
Do not attempt to recharge non-rechargeable batteries
with the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the plug
If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
USE
USE OF BATTERY
Always remove battery from tool before making any
adjustment or changing any accessory, in order to
reduce the risk of starting the tool accidentally 4
Charging battery 5
- battery of new tools is not fully charged
- plug charger into power source
- light A will turn on
- insert battery correctly into charger, so that it makes
contact and is not hindered by foreign objects
- light A will blink indicating that the battery is receiving
a charge (5a)
8