Transport; Storage; Care And Service - Kärcher HD 9/100-4 Cage Classic Manual Del Usuario

a The trigger must independently return to the ini-
tial position and engage in the safety latch when
released.
b It should only be possible to actuate the trigger
when the safety latch is actuated.
Ending operation
1. Release the trigger.
2. Turn the power switch to "0/OFF".
3. Close the water inlet.
4. Pull the trigger of the trigger gun until the device is
depressurised.
5. Release the trigger.
Dump gun: The safety latch secures the trigger
against unintentional operation.
6. Dry shut: Pivot the safety latch downward.
7. Unscrew the water supply hose from the device.
8. Pull the mains plug out of the socket only when your
hands are dry.
9. Store the mains connection cable, high-pressure
hose and accessories with the device.

Transport

 Driving the device: Pull the parking brake pedal to
the rear and push the device using the push handle.
 Parking the device: Press the parking brake pedal
forward.
 Transporting the device in a vehicle: Secure the de-
vice in accordance with the respectively applicable
guidelines to prevent it from slipping or overturning.
 Transporting the device with a forklift: Secure the
device against falling using the transport eyelets ac-
cording to the applicable guidelines.
Crane transport
DANGER
Improper crane transport
Risk of injury from a falling device or falling objects
Observe the local regulations for accident prevention
and the safety instructions.
Check the crane lifting gear for damage before each
crane transport.
The device may only be transported with a crane by per-
sons instructed in the operation of the crane.
Check the lifting gear for damage before each crane
transport.
Check the crane loading brace for damage before each
crane transport.
Lift the device only at the middle of the crane loading
brace.
Do not lift the device by the electric motor ring bolt.
Do not use an slinging chains.
Secure the lifting gear against unintentional unhooking
of the load.
Remove the spray lance with high-pressure gun and
other loose objects before transporting by crane.
Do not transport any objects on the device during the
lifting operation.
Do not stand under the suspended load.
Ensure that no persons are in the hazard zones of the
crane.
Do not leave the device handing unattended on the
crane.
1. Attach the lifting gear to the middle of the crane
loading brace.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transport
and storage.
 Store the device indoors only.
 Storage temperature -20 °C...+40 °C
 No corrosive atmosphere.
 Vibration-free storage location.
 Turn the motor shaft manually by a quarter turn once
a week.
High-pressure hoses:
 Completely drain the hose.
 Close all openings.
 Protect the fittings with protective caps.
 Observe the maximum storage duration. Ageing im-
pairs the material properties.
 Store free of tension and lying down.
 Store in a cool, dry and dust-free place.
 Avoid direct sunlight or UV radiation.
 Shield from sources of heat.
 Avoid the vicinity of ozone sources (e.g. fluorescent
light sources, mercury-vapour lamps).
 Do not bend beyond the smallest permissible ´bend-
ing radius.
ATTENTION
Frost
Destruction of the device through freezing water
Drain all water from the device.
Store the device in a frost-free location.
If frost-free storage is not possible:
1. Drain the water.
2. Blow out the device with compressed air.
3. Pump commonly available anti-freeze through the
device.
Note
Use commonly available, Glycol-based vehicle anti-
freeze. Observe the handling instructions of the anti-
freeze manufacturer.

Care and service

DANGER
The device can start unintentionally.
The high-pressure water jet or impelled parts can cause
injuries.
Set the power switch to 0/OFF and actuate the trigger of
the high-pressure gun until the device is depressurised
before starting maintenance.
Note
Old oil may only be disposed of at designated collection
points. Please dispose of any old oil at these locations.
Polluting the environment with old oil is punishable by
law.
Safety inspection/maintenance contract
You can agree on regular safety inspections or close a
maintenance contract with your dealer. Please seek ad-
vice on this.
Maintenance intervals
Each time before use
 Check the mains cable for damage.
Have a damaged cable replaced immediately by the
authorised Customer Service or a qualified electri-
cian.
English

Storage

Frost protection
21