Gwarancja I Serwis - VERTO 51G203 Instrucciones De Uso

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
Ul. Pograniczna 2/4
02-285 Warszawa
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna na platformie internetowej gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na gtxservice.pl. Zeskanuj kod QR i wejdź:
tel. +48 22 573 03 85
fax. +48 22 573 03 83
e-mail [email protected]
do napraw gwarancyjnych
GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME, READ THIS
INSTRUCTION MANUAL AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
ANGLE GRINDER, SAFETY WARNINGS
Safety guidelines for grinding, sanding with sandpaper, working
with wire brushes and cutting using the grinding wheel.
• This power tool can be used as a regular grinder, sander for
sanding with sandpaper, grinder for grinding with wire brushes
and for cutting with a cut-off wheel. Observe all safety guidelines,
instructions, descriptions and data provided with the power tool.
Failure to observe the following recommendations may cause danger of
electric shock, fire and/or serious injuries.
• This power tool cannot be used for polishing. When the power tool
is used for other works than it is designed for, it may contribute to hazards
and injuries.
• Do not use equipment, which is not designed and recommended
by the manufacturer specifically for this device. The fact that it can
be fastened to the power tool, does not guarantee safe operation.
• The permissible rotational speed of a working tool used cannot be
lower than the maximum rotational speed given on the power tool.
A working tool rotating faster than the permissible speed may break and
its parts may chip off.
• The outside diameter and thickness of a working tool must
correspond to dimensions of the power tool. A working tool of
incorrect dimensions may not provide sufficient control and covering of
the power tool.
• Working tools with threaded inserts must perfectly fit the thread
in the spindle. In case of working tools that are fastened using
a flange, the hole diameter of a working tool must fit the flange
diameter. Working tools, which cannot be precisely seated in the power
tool, rotate unevenly, vibrate heavily and may result in loss of control over
the power tool.
• Under no circumstances, should damaged working tools be used.
Before the power tool is used, accessories such as cut-off wheels
should be checked for chips and cracks, grinding wheels should
be checked for cracks, abrasion or heavy wear, while wire brushes
for loose or broken wires. When the power tool or a working tool is
dropped, it must be checked for damage or another, undamaged
tool should be used. If a working tool is checked and fastened,
the power tool should be switched on for a minute at the highest
speed, paying attention so that the operator and bystanders are
beyond the zone of the rotating tool. Damaged working tools often
break in this test period.
• Always wear personal protective equipment. Depending on a
type of work, a full face mask, eye protection or safety glasses
should be worn. A dust mask, ear protection, protective gloves
or a special apron protecting against small particles of abrasive
material and workpiece should be worn, if needed. Protect your
eyes against airborne foreign bodies occurring during operation. A dust
mask and protective mask for the respiratory system must filter dust
occurring during work. The influence of noise for a longer period of time
may lead to deterioration of the hearing.
• Always make sure bystanders are in a safe distance from the
power tool reach zone. All people staying in the vicinity of the
operating power tool must use personal protective equipment.
Chips of a workpiece or broken working tools may chip off and cause
injuries also beyond the direct reach zone.
• When works are performed, during which the power tool may
encounter hidden electric conductors or own power cord, the
power tool should be held by the isolated surfaces of the handle.
A contact with the power mains network may transfer voltage onto metal
parts of the power tool, which may result in electric shock.
• The power cord must be kept away from the rotating working
tools. When the control over the tool is lost, the power cord may be cut
or caught, and your hand or the entire arm may get into the rotating
working tool.
11
ANGLE GRINDER
51G203