Presets - Hughes & Kettner Black Spirit 200 FLOOR Manual De Instrucciones

4.3 Connections and control features on the right
●
9
Mode: Use this sliding switch to set the amp to Preset, Stompbox or
Direct 7 mode. See section 5.1 for more on this.
Tip: You can also footswitch Stompbox and Direct 7 modes on and
off without engaging the sliding switch. Press and hold the following
combinations of buttons for two seconds to do this:
• TAP + B = Stompbox mode on/off
• TAP + Bank Up = Direct 7 mode on/off
Heads up: Whatever mode the sliding switch is set to when you switch the
amp off will be activated when you switch the amp back on again.
●
10
Control 1 +2: You can connect expression pedals – we like the Yamaha FC 7 – or simple footswitches such as the recommended Hughes
& Kettner FS-1 to both connectors to assign more control functions to
Black Spirit 200 Floor. This lets you control all programmable functions of
the Black Spirit 200 Floor remotely, in real time. For example, you could
vary the amount of reverb with an expression pedal, turn the Noise Gate
on and off with your foot, or adjust the gain level on the fly with a pedal
without taking your hands off the guitar. Experience teaches that guitarists
like to activate and deactivate the Boost function via footswitch without
having to switch presets, and adjust the volume level with a pedal. This is
why we assigned Control 1 to Boost and Control 2 to Volume. Read section
7.4 if you wish to change these factory defaults and assign other functions
to Control 1 and 2.

5 Presets

5.1 Accessing Presets
You can select Black Spirit 200's presets of Floor on the amp, via MIDI or
in an app connected via Bluetooth. You have three modes for accessing
presets. Select the desire mode using the sliding switch on the right or a
combination of buttons.
CLEAN CRUNCH LEAD
1 2 3
1 Preset mode:
Preset mode offers 128 presets, divided into 32 banks of 4 presets each.
Use Preset buttons A, B, C, D and the Bank Up/Down buttons with the
arrows pointing up and down to call up presets.
Preset buttons A, B, C, D: Presets within a bank activate directly, that is,
you can switch straight from A to B within the same bank. The LEDs above
the A, B, C, and D buttons indicate the selected preset.
9 10
ULTRA MOD DLY BOOST
4 5 6 7
Bank Up/Down :
In Preset mode, Black Spirit 200 Floor's display always shows the
currently selected bank number. To activate a preset in another bank, you
have to first preselect this bank using the Up/Down buttons. The currently
selected preset stays activated while you're doing this so you can keep
playing with the same sound. This preselected bank number will flash in
the display until you active a new preset in the target bank by pressing
one of the A, B, C or D Preset buttons. The amp will not switch to the
newly selected preset until you do this.
Tap: Tap offers you a quick, convenient way of adjusting delay time. It's
particularly handy on stage: simply tap your foot on the Tap button in time
with the beat to match the delay time to the tempo. See section 3.1 for
more info.
2 Stompbox mode:
The display reads "Sb" when you move the sliding switch to Stompbox
mode. In this mode, the FSM-432 MK III's buttons serve to switch
channels directly rather than select presets. They also let you activate
and deactivate Modulation effects, Delay and Boost independently at the
touch of a button. In this mode, the connected amp works just like a
conventional setup with an amp and outboard pedals and stompboxes.
The four buttons A, B, C, D are now assigned to the amp's four Clean,
Crunch, Lead and Ultra channels. The amp remembers the Gain, Volume,
Bass, Mid, Treble, Sagging, Resonance and Presence settings automatically
for every channel, so you don't have to store them manually. It does this
in Stompbox mode only. This mode is independent of Preset mode, so
changes made here will not erase or overwrite any of its presets.
Heads up: However, you can store your settings even in Stompbox mode.
Simply press and hold Store for more than three seconds, and the amp
will store the current settings to the preset most recently selected in Preset
mode before you switched over to Stompbox mode. You can easily select
a new memory slot if you do not wish to overwrite the most recently
selected preset. To do so, slide the Mode switch over to Preset mode,
briefly press the Store button, and then select a memory slot using the
Up/Down buttons and the preset A, B, C, or D buttons.
The onboard effects, FX loop and Noise Gate are global control features
in Stompbox Mode. In other words, their settings apply to all channels.
You can switch Modulation FX, Delay and Boost on and off separately
using the Mod, Delay and Boost buttons. You can also adjust the Reverb
via an added footswitch or pedal connected to one of the Controller
inputs on Black Spirit 200 Floor. Read section 7.4 to learn more.
Heads up: Generally speaking, we recommend using Stompbox mode
when you're working with a few basic sounds and just want to switch
channels on the fly. Preset mode is the better option when you're working
with a fixed set list and want to program the various sounds in a certain
order. But what if you want to have it both ways – that is, the Stompbox
mode's direct switching options while the amp is in Preset mode? Then
simply connect additional footswitches to the Controller inputs (see also
section 7.4).
3 Direct 7 mode:
In Direct 7 mode, you can assign one preset to each of the seven buttons
on the built-in MIDI board to access seven presets directly without having
to change banks. You do not need to program and save new presets to this
end. Simple assign your favorite presets or the main presets for the next
Black Spirit 200 Floor – Manual 1.0
9