Beko ADV5810 Manual Del Usuario página 32

it is turned back on, it will start at the same speed it was
in when switched off.
• Controls (Fig.26):
NOTE: with this command the appliance can also be
controlled with a remote control to be requested as an
accessory.
Power key (A) = If the appliance is set up to support
other functions such as automatic openings, room lights,
etc., this key enables these functions.
Attention! In some models this key does not enable any
function and if pressed it turns on the corresponding LED
for approximately 15 sec.
-OFF key (B) = Key for reducing speed and switching off.
+ON key (C) = From the OFF position, by pressing the
C key once, the motor goes to 1st speed, twice for 2nd
speed, three times for 3rd speed; at each speed change,
the LED changes colour.
By pressing the B key, the speed reduces and the LED
turns to the typical colour of the speed.
Intensive key (D) = With the motor running and at any
speed, pressing the D key inserts the INTENSIVE speed
(4th speed) for 10 minutes. During this function the
LED flashes, and the speed LED previously set turns out.
After 10 minutes, the hood returns for the last set speed
with the relative LED indication.
- If you wish to deactivate the function before the 10
minutes are up, press the B key.
- The INTENSIVE speed function will not activate when
the hood is off.
Light key (E) = Pressing this key adjusts light intensity.
- There are three light intensity levels: high, medium, low.
From the off position, press once for the high level, twice
for the medium level, three times for the low level, and
four times to turn the lights off.
Light intensity is cyclical: high, medium, low, off.
Timer key (F) = With any speed inserted (except for
intensive speed) pressing this key activates the Timer
function. The LED of the Timer key flashes and the speed
LED remains on.
- 15 minutes after the count is over, the hood turns off
(motor and lights).
• By pressing the B key for 2 seconds (with the hood up)
the "clean air" function is activated.
This function activates the motor for 10 minutes everyr
hour at 1st speed, during which the LED corresponding
to the B key remains on.
During the remaining 50 minutes, the LED of the C key
flashes with the motor off, while the B key LED remains
on, indicating that the function is still active.
In order to deactivate the "clean air" function, press any
key except for the LIGHTS.
• Anti-grease/active charcoal filter saturation:
- After 30 h of operation, the LED of the B key begins to
flash; this means that the anti-grease filters must be
washed.
- After 120 h of operation the LED of the E key begins
to flash; this means that the charcoal filter must be
washed or replaced.
Once the clean filter has been put back in place, the
electronic memory must be reset by pressing the C key
for approximately 4 sec. until it stops flashing and the
30 h/120 h setting restarts from zero.
• Commands (Fig.27) :
A = Light Key Turn on/off lights.
B = ON/OFF Key Turn on/off the hood.
The equipment switches on at the 1st speed.
To turn off the hood press key B.
C = Display Indicates the speed of the selected motor
and activation of the timer.
D = Key Increases and decreases the speed of the motor
with a cyclical pattern, 1°-2°- 3° ... 1°-2°- 3° speed.
By pressing the key for 3 seconds the INTENSE function
comes into operation for 6 minutes, on the C display the
number 4 starts flashing.
At the end of the minutes the engine will start operating
at the previously set speed.
To deactivate the intense speed, before the set time,
press the B key and the hood turns off, but not if the
lights are on.
E = Timer key With any speed entered (excluding In-
tense speed) by pressing the key the timer function is
activated for 15 min. At the end of the count the hood
turns off (motor and any lights that are on).
To turn off the Timer function, before the pre-set time,
press the B key and the hood turns off, or by pressing
the timer key again it turns off but the hood continues
to operate.
• S aturation Active carbon/Anti-grease filters:
- After 30 h of operation, with the hood ON on display C
, the letter F starts to flash which means that the anti-
grease filters have to be washed.
Once the clean filter is replaced you must reset the elec-
tronic memory, with the hood off press key B and D for 5
sec. until the display C shows the letter F fixed for 2 sec.
-After 120 h of operation, with the hood ON on display C
the letter C starts to flash which means that the carbon
filters have to be washed or replaced.
Once the clean filter is replaced you must do a double re-
set so with the hood off press key B and D for 5 sec. until
the display C shows the letter F fixed for 2 sec.
Repeat and press key B and D for 5 sec. until display C
shows the letter C fixed for 2 sec. .
• Commands (Fig.28)
A = ON/OFF key
Turns the hood on/off.
By pressing key A the LED flashes for 2 sec. then remains
fixed and the equipment starts in 1° speed.
To turn the hood off press key A again, the LED flashes
for 2 sec. then it turns off.
B = FIRST SPEED KEY
C = SECOND SPEED Key/TIMER function
- Key C also activates the TIMER function.
- The key flashes for the full duration of the TIMER.
- With any speed entered (excluding Intense speed where
applicable) by pressing C for about 3 seconds the TIMER
function is activated for 15 min. At the end of the count
the hood turns off (motor and any lights that are on).
- To deactivate the Timer function, before the pre-set
time, press any key except the F key for ON/OFF Lights.
D = THIRD SPEED key/ INTENSE SPEED Function
- Key D also activates the INTENSE SPEED function.
- The key flashes for the full duration of the INTENSE
SPEED function.
- By pressing the key for 3 seconds the INTENSE function
comes on for 6 minutes.
- At the end of the minutes the engine will start operating
- 30 -