Tabla de contenido
Idiomas disponibles
Idiomas disponibles
on, or if the current supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 12.).
11. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model
designation of your power tool in order to select the
correct accessory.
See page 4.
A Roughing disc (always use with safety guard
attached)
B Louver disc (always use with safety guard
attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with safety guard or
parting safety guard attached)
F Parting safety guard with guide slot (place on
machine and secure with screws.) (with adapter
for connection to a suitable dust extractor for
extraction of stone dust generated when cutting
stone slabs.)
G Hand guard (for attaching under the additional
side-mounted handle.)
H Steel wire brushes (always use with the hand
guard attached.)
I Bench cut-off stand
J Adjusting nut (12)
K "Quick"clamping nut (1)
For complete range of accessories, see
www.metabo.com or refer to the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
14. Technical Specifications
Explanation of details on page 2 . Subject to
changes serving technical progress.
D
= Maximum sanding disc diameter
max
t
= max. permitted thickness of clamping
max,1
shank on accessory when using clamping
nut (12)
t
= max. permitted thickness of clamping
max,2
shank on accessory when using
"Quick"clamping nut (1)
t
= Roughing disc/Parting disc:
max,3
max. permitted thickness of accessory
M
= Spindle thread
l
= Length of the grinding spindle
n
= No-load speed (maximum speed)
P
= Nominal power input
1
P
= Power output
2
m
= Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
= Vibration emission value (sanding
h, SG
surfaces)
a
= Vibration emission value (sanding with
h, DS
sanding pad)
K
= Uncertainty (vibration)
h,SG/DS
Typical A-effective perceived sound levels:
L
= Sound pressure level
pA
L
= Acoustic power level
WA
K
, K
= Uncertainty
pA
WA
Wear ear protectors!
ENGLISH en
17
Tabla de contenido
