Tabla de contenido
Idiomas disponibles
Idiomas disponibles
en
ENGLISH
Getting the machine ready for operation
Turn the lever (14) anti-clockwise up to the stop.
The motor section swings upwards.
8.2
Correcting the saw blade angle
The saw blade angle has been adjusted at the
factory.
If necessary, the saw blade angle can be adjusted
for 0° and for 45°. Turn the adjusting screw (7) (for
0°) or (3) (for 45°).
9. Cleaning
Remove battery pack from machine.
Dust deposits must be regularly removed from the
machine. This includes cleaning the ventilation slits
on the motor with a vacuum cleaner. Make sure that
the safety appliances are in perfect working order
(e.g. the motor section must move freely, return
automatically, smoothly and precisely to its end
position).
f
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See page 5.
A Rip fence
B Guide rail
C Fast-action clamp clip. To secure the guide rail.
D Circular saw blades. For clean cutting results
for straight and cross cuts in soft and hard
wood.
E Battery charger
F Battery packs with different capacities. Only
buy battery packs only with voltage suitable for
your power tool
G Metabo universal vacuum cleaner
H Suction hose
For a complete range of accessories, see
www.metabo.com or the catalogue.
11. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
12. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
18
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
13. Technical Specifications
Explanatory notes regarding the specifications on
page 4.
Subject to change in accordance with technical
progress.
U
= Voltage of battery pack
n
= idle speed
0
T
= maximum depth of cut
max
T
= adjustable depth of cut (90°)
90°
T
= adjustable depth of cut (45°)
45°
A
= adjustable angular cut angle
Ø
= saw blade diameter
d
= saw blade drill diameter
a
= max. base body thickness of the saw
blade
b
= max. cutting width of saw blade
m
= weight
Measured values determined in conformity with EN
62841.
Permitted ambient temperature during operation:
-20 °C to 50 °C (limited performance with
temperatures below 0 °C). Permitted ambient
temperature for storage: 0 °C to 30 °C
direct current
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a
= Vibration emission value
h, D
(Sawing chip board)
K
= Uncertainty (vibration)
h,D
Typical A-effective perceived sound levels:
L
= sound-pressure level
pa
Tabla de contenido
