Protecting The Environment - Black+Decker BDCDS12 Manual De Instrucciones

ENGLISH
Charging the battery (Not supplied) (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery, insert the USB charger (5) into the
u
Battery.
Plug the charger into a suitable power source and switch
u
on.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Fitting and removing the battery (Not supplied)
(fig. B)
To fit the battery, line it up with the receptacle on the tool.
u
Slide the battery into the receptacle and push up until the
battery snaps into place.
To remove the battery, push the release button (5) while at
u
the same time pulling the battery out of the receptacle.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting sanding sheets (Fig. C )
Attach a sanding sheet (7) by pressing the 'hooked' velcro
u
side to the 'looped' velcro underside of the sanding base
(3).
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
To switch the tool on, depress the on/off switch (1) at the
u
position I.
To switch the tool off, depress the on/off switch (1) at the
u
position O.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool or remove the battery pack.
6
(Original instructions)
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.

Protecting the environment

Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Input voltage V
dc
No - load speed min
Oscilating angle °
Sanding base surface mm
Weight kg
Battery (not supplied)
Voltage V
dc
Capacity Ah
Type
Charger
Input voltage V
AC
Output voltage V
DC
Output current A
Approx. charge time Hours
L (sound pressure) 76,9 dB(A), Uncertainty (K) 3 dB(A)
pA
L (sound power) 87,9 dB(A), Uncertainty (K) 3dB(A)
WA
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (handle) (a
EC declaration of conformity
%
MACHINERY DIRECTIVE
Sander - BDCDS12
BDCDS12
11000 OPM
-1
2
0.63 (with battery 0.88)
BDCB12
Lithium-Ion
100-240V
) 4,7m/s , uncertainty (K) 1,5 m/s
2
h
12
2.8
5078
12
1.5
5V
1
1.5
2