Tabla de contenido
Idiomas disponibles
Idiomas disponibles
TAB: 7509
Manual programming
Basic interphone/monitor programming is as follows:
- Programming ID, which must be performed on the interphone that re-
ceives the call individually or on the first interphone of a group of inter-
phones/monitors with simultaneous calls (master interphone).
- Programming secondary ID, which must be done for interphones asso-
ciated with a master interphone/monitor.
- Programming programmable buttons or changing the default setting of
supplementary buttons, for auxiliary services or intercommunicating calls.
Programming must be carried out with the system switched on, without
active communication and only after the interphones/monitors have been
connected to the system and the entrance panels have been programmed.
N.B.: all the programming or deletion phases must be performed with
the interphone/monitor handset lifted and held against the user's ear.
Programming ID identification code
The identification code is programmed by means of a main entrance panel
(MASTER), already configured and present in the system.
The interphone is supplied without associated identification code. To verify
this, press the lock release button and the interphone should emit an audible
signal (triple beep).
To program the ID, proceed as follows:
1) Lift the handset.
2) Press buttons B and A simultaneously and hold them down until LED F
(ringtone mute) begins flashing.
3) Release the buttons.
4) Press button C and hold it down (for 2 sec.) until the handset emits
an audible signal and communication between the interphone and the
outdoor entrance panel begins.
5) Release button C.
Important: you will have 5 s in which to press button C (as indicated in
step 4). If button C is not pressed within the 5 s, steps 1, 2 and 3 must
be repeated.
6) You now have approx 30 seconds to assign the ID code of the external
entrance panel:
-
in the case of an alphanumeric panel, key in the primary ID and
press the "bell" button to confirm.
-
in the case of a push-button entrance panel, press the button you
want to use to call the interphone.
Important: If the system already contains an interphone with the same
associated identification code, the entrance panel emits a low tone and the
process must be repeated from the start in order to assign a different code.
Programming secondary ID
Programming the secondary ID is only necessary when you want more than
one interphone/monitor to ring in response to the same pushbutton or call
code. The interphones/monitors that are to ring at the same time are associ-
ated with the same group. The "master" interphone/monitor is programmed
first by means of the "identification code programming" procedure described
above, while the additional group interphones/monitors are programmed
with the secondary identification code.
The maximum number of monitors that can be associated with the same
group without using SaveProg software is 3 plus a master unit. Alternatively,
a SaveProg software can be used to program activation of the ringtone of
all video door entry units and the monitor of only the master unit. Before
answering from a secondary video door entry unit, the relevant monitor can
be turned on by means of the self-start button.
To program the secondary ID, proceed as follows:
1) Lift the handset.
2) Press buttons B and A simultaneously and hold them down until LED F
(ringtone mute) begins flashing.
3) Release the buttons.
4) Press buttons A and C simultaneously and hold them down (for 2 sec.)
until the handset emits an audible signal and communication between
12
the interphone and the outdoor entrance panel begins.
5) Release buttons A and C.
Important: you will have 5 s in which to press buttons A and C (as indicated
in step 4). If buttons A and C are not pressed within the 5 s, steps 1, 2 and
3 must be repeated.
6) You now have approx 30 seconds to assign the ID code of the external
entrance panel:
-
in the case of an alphanumeric panel, key in the primary ID and
press the "bell" button to confirm.
-
in the case of a push-button entrance panel, press the button you
want to use to call the interphone.
Important: When programming the primary and secondary ID, the inter-
phones undergoing programming automatically acquire a code that de-
pends on the association with the button or code used to call the outdoor
entrance panel. Correspondence between the primary ID and the respective
secondary ID codes is provided in the table below.
Example: If ID = 8 is given to a second interphone, the automatic second
interphone identification attribution procedure will automatically assume ID
= 72 (see table).
When a call is made to ID = 8, both interphones will chime and both can be
used to answer. If, on the other hand, in the case of an alphanumeric panel
you enter 72 (the ID automatically assigned by the procedure), a chime is
emitted by the interphone for which the secondary ID assignation procedure
was carried out and only this interphone can be used to answer the call.
Table of primary and corresponding secondary ID codes:
Secondary ID
Primary ID
1
2
1
51
52
2
54
55
3
57
58
4
60
61
5
63
64
6
66
67
7
69
70
8
72
73
9
75
76
10
78
79
11
81
82
12
84
85
13
87
88
14
90
91
15
93
94
16
96
97
17
99
100
18
102
103
19
105
106
20
108
109
21
111
112
22
114
115
23
117
118
24
120
121
25
123
124
Important: to delete from a group, the programming deletion procedure de-
scribed in the "Default data restore procedure" section must be performed.
Button programming
Important: without SaveProg software, the only functions that can be as-
signed are intercommunication, specific entrance panel self-activation,
restoring buttons programmed by the installer to their default settings and
restoring default data.
Button programming procedure for intercommunicating calls
To program the buttons, proceed as follows:
1) Press the "talk/listen" button or lift the handset (depending on model
installed) for the interphone/monitor TO BE CALLED.
2) Lift the handset to be programmed (the caller handset).
3) Press buttons B and A on the interphone to be programmed (caller)
simultaneously and hold them down until LED F (ringtone mute) begins
flashing.
4) Release buttons B and A.
5) Press and hold down the button to be programmed (e.g. E1, E2, E3, E4).
EN
Secondary ID
Primary ID
1
2
3
26
126
127
53
27
129
130
56
59
28
132
133
29
135
136
62
30
138
139
65
68
31
141
142
32
144
145
71
74
33
147
148
77
34
150
151
35
153
154
80
83
36
156
157
86
37
159
160
38
162
163
89
92
39
165
166
40
168
169
95
98
41
171
172
101
42
174
175
43
177
178
104
107
44
180
181
110
45
183
184
113
46
186
187
116
47
189
190
119
48
192
193
122
49
195
196
125
50
198
199
3
128
131
134
137
140
143
146
149
152
155
158
161
164
167
170
173
176
179
182
185
188
191
194
197
200
Tabla de contenido
