ESAB Cutmaster 120 Manual De Instrucciones página 77

ESAB CUTMASTER 120
Type Torch: SL100 With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output Amperage Speed (Per Minute)
Inches mm (Cat. No.) Volts(VDC) (Amps) Inches Meters
0,250 6,4 9-8253 136 120 180 4,57
0,375 9,5 9-8253 144 120 100 2,54
0,500 12,7 9-8253 149 120 60 1,52
0,625 15,9 9-8253 153 120 40 1,02
0,750 19,1 9-8253 157 120 30 0,76
1,000 25,4 9-8253 162 120 20 0,51
1,250 31,8 9-8253 165 120 10 0,25
Type Torch: SL100 With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output Amperage Speed (Per Minute)
Inches mm (Cat. No.) Volts(VDC) (Amps) Inches Meters
0,250 6,4 9-8253 144 120 190 4,83
0,375 9,5 9-8253 148 120 120 3,05
0,500 12,7 9-8253 152 120 75 1,91
0,625 15,9 9-8253 162 120 45 1,14
0,750 19,1 9-8253 163 120 35 0,89
1,000 25,4 9-8253 168 120 20 0,51
NOTE!
* Gas pressure shown is for torches with leads up to 25' / 7.6 m long. For 50' / 15.2 m
leads, refer to Section "Set Operating Pressure" on page <?>.
** Total flow rate includes plasma and secondary gas flow.
4T-18
OPERATION
Type Material: Stainless Steel
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas Press Flow (CFH) Pierce Pierce Height
Inches mm psi* bar Plasma Total** Delay (Sec) Inches
0,13 3,2 75 5,2 180 360 0,20 0,20
0,13 3,2 75 5,2 180 360 0,40 0,20
0,13 3,2 75 5,2 180 360 0,80 0,20
0,15 3,8 75 5,2 180 360 1,20 0,20
0,15 3,8 75 5,2 180 360 NR NR
0,15 3,8 75 5,2 180 360 NR NR
0,15 3,8 75 5,2 180 360 NR NR
Type Material: Aluminum
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas Press Flow (CFH) Pierce Pierce Height
Inches mm psi* bar Plasma Total** Delay (Sec) Inches
0,13 3,2 75 5,2 180 360 0,20 0,20
0,13 3,2 75 5,2 180 360 0,50 0,20
0,15 3,8 75 5,2 180 360 0,70 0,20
0,15 3,8 75 5,2 180 360 1,00 0,20
0,15 3,8 75 5,2 180 360 NR NR
0,15 3,8 75 5,2 180 360 NR NR
Manual 0-5398
mm
5,1
5,1
5,1
5,1
NR
NR
NR
mm
5,1
5,1
5,1
5,1
NR
NR
Manual 0-5398
This Page Intentionally Blank
OPERATION
ESAB CUTMASTER 120
4T-19