Water Ace R33WU Manual Del Usuario página 2

READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential for
personal injury.
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
warns about hazards that can cause serious per-
sonal injury, death or major property damage if ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which are
important but not related to hazards.
GENERAL SAFETY
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
To avoid serious injury and/or property damage, read and fol-
low these rules and instructions carefully.
Risk of electric shock. Can burn or kill. This
pump only for use in portable, self-contained fountains no
larger than 5 feet in any dimension.
1. Pump is designed for use with clean, cold, fresh water.
Pump water only with this pump.
2. Do not lift pump by power cord at any time. Attempting
to lift or support the pump by the power cord can damage
the cord and cord connections, and will void warranty.
Always lift the pump by the lifting handle.
3. Meet National Electrical Code, Canadian Electrical Code,
and local codes for all wiring. The National Electric Code
requires installation of a ground fault circuit interrupter
(GFCI) in the branch circuit supplying fountain pumps and
other pond equipment. Purchase a GFCI at your local elec-
trical supply dealer.
4. Installation must comply with all local codes
pertaining to outdoor waterfall, fountain, pond
and utility pumps.
5. Know the pump application, limitations, and
potential hazards.
6. Disconnect the power before servicing.
7. Release all pressure within the system before servicing any
component.
PERFORMANCE
Motor
Model HP (0 m)
R33WU 1/3 2,400 (9,085)
WA-253P7550
GPH (LPH) AT TOTAL FEET (M)
0 5
(1.5 m)
1,920 (7,628) 1,380 (5,224)
8. Drain all water from the system before servicing.
9. Secure the discharge line before starting pump. An unse-
cured discharge line will whip, possibly causing personal
injury and/or property damage.
10. Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
11. Periodically inspect the pump and system components.
Keep the pump inlet free of debris and foreign objects.
Perform routine maintenance as required.
12. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly lighted
– replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
13. This equipment is only for use on 115 volt (single phase)
and is equipped with an approved 3-conductor cord and 3-
prong, grounding-type plug.
Hazardous voltage. Can shock, burn or cause
death. To reduce risk of electric shock, pull plug before servic-
ing. This pump has not been investigated for use in swimming
pool areas. Pump is supplied with a grounding conductor and
grounding-type attachment plug. Be sure it is connected only
to an individual branch circuit with a properly grounded
grounding-type receptacle. Where a 2-prong wall receptacle is
encountered, it must be replaced with a properly grounded 3-
prong receptacle installed in accordance with codes and ordi-
nances that apply.
14. Make certain power source conforms to requirements of
your equipment.
15. Protect the electrical cord from sharp objects, hot surfaces,
oil, and chemicals. Avoid kinking cord. Replace or repair
damaged or worn cords
immediately.
16. Do not touch an operating motor. Motors can operate at
high temperatures.
17. Do not handle pump or pump motor with wet hands or
when standing on wet or damp surface, or in water.
DESCRIPTION
This submersible pump is designed for use as a waterfall/foun-
tain or as a utility pump. The unit is equipped with a 3-prong
grounding-type power cord.
Ball bearings on the motor shaft never need lubrication.
Automatic reset thermal protection.
10 15
(3 m) (4.6 m)
780 (2,953)
2
No Flow
20 At Height
(6.1 m) Shown Below
160 (606) 22' (6.7 m)