Transport; Maintenance; Storage; Electrical Connection - Scheppach HM135B Traducción De Las Instrucciones Originales De Funcionamiento

• Move the guide bar into position and tighten the
screw (f) again.
• Before continuing your work make sure that all sa-
fety devices are in good working condition.
• Important! Every time that you change the saw
blade (7), check to see that it spins freely in the
table insert (11) in both perpendicular and 45° ang-
le settings.
• Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser/LED (Fig. 10,15)
• To switch on: Move the ON/OFF switch of the la-
ser (35) to the "1" position. A laser line is projected
onto the material you wish to process, providing an
exact guide for the cut.
• To switch off: Move the ON/OFF switch of the la-
ser (35) to the "0" position.
8.12 Adjusting the laser (Fig. 10)
If the laser (34) ceases to indicate the correct cutting line,
you can readjust the laser. To do so, open the screws
(36) and set the laser by moving sideways to that the la-
ser beam strikes the teeth of the saw blade (7).
9. Transport (Fig. 1,2)
• Tighten the set screw (26) in order to lock the ro-
tary table (16)
• Activate the release lever (3), press the machine
head (5) downwards and secure with the safety pin
(24). The saw is now locked in its bottom position.
• Fix the saw's drag function with the locking screw
for drag guide (23) in rear position.
• Carry the equipment by the fixed saw table (17).
• When reassembling the equipment proceed as de-
scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to
time using a cloth. In order to extend the service life
of the tool, oil the rotary parts once monthly. Do not
oil the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the carbon brushes after the first 50 operat-
ing hours with a new machine, or when new brushes
have been fitted. After carrying out the first check,
repeat the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes
are found to be usable following removal, it is pos-
sible to reinstall them.
28 GB
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brushes, saw blade, batteries,
table inserts, dust collecting bags, V-belts
* Not necessarily included in the scope of delivery!

11. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer's mains connection as well as
the extension cable used must also comply with
these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely se-
lectable connection point is not allowed.
• Given unfavourable conditions in the power supply the
product can cause the voltage to fluctuate temporarily.
• The product is intended solely for use at connec-
tion points that
a) do not exceed a maximum permitted supply
impedance "Z" (Zmax = 0.382 Ω), or
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Damaged electrical connection cable.
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.