Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INDEX
1.
BURNER DESCRIPTION . . . . . . . . . . . .
1.1 Burner equipment . . . . . . . . . . . . . . . . .
2.
TECHNICAL DATA . . . . . . . . . . . . . . . .
2.1 Technical data . . . . . . . . . . . . . . . . . . . .
2.2 Accessories . . . . . . . . . . . . . . . . . . . . . .
2.3 Overall dimensions . . . . . . . . . . . . . . . .
2.4 Firing rate . . . . . . . . . . . . . . . . . . . . . . . .
3.
INSTALLATION . . . . . . . . . . . . . . . . . . .
3.1 Heat generator fixing . . . . . . . . . . . . . . .
3.2 Working position . . . . . . . . . . . . . . . . . .
3.3 Fuel supply . . . . . . . . . . . . . . . . . . . . . .
3.4 Hydraulic systems . . . . . . . . . . . . . . . . .
3.5 Electrical wiring . . . . . . . . . . . . . . . . . . .
1.
BURNER DESCRIPTION
Two stage light oil burner.
ATTENTION
If the burner is to be combined with a hot air generator in Germany (WLE according to DIN 4794), the con-
trol box must be replaced with a Riello 550 SMD control box (remove the bridge), and the flame sensor
must be replaced with the amplified type (both fully interchangeable). This control box, combined with the
"remote reset kit" (which can be ordered separately), means that the burner can be reset by remote control.
1 - Pump
2 - Electronic start delaying device
3 - Control-box
4 - Reset button with lock-out lamp
5 - Flange with insulating gasket
6 - 2 nd stage air damper adjustment
assembly
7 - Nozzles holder assembly
8 - Photoresistance
9 - Hydraulic jack
10 - 4 pole socket
11 - 2 nd stage valve
12 - 1 st stage valve
13 - Valve casing assembly
1.1 BURNER EQUIPMENT
Flange with insulating gasket . . . .No. 1
Screw and nuts for flange . . . . . .No. 1
7 pin plug . . . . . . . . . . . . . . . . . . .No. 1
2902
1
4.
WORKING . . . . . . . . . . . . . . . . . . . . . . .
1
4.1 Combustion adjustment. . . . . . . . . . . . . .
4.2 Recommended nozzles . . . . . . . . . . . . . .
2
4.3 Combustion head setting. . . . . . . . . . . . .
2
4.4 Electrodes adjustment. . . . . . . . . . . . . . .
2
4.5 Pump pressure and air output . . . . . . . . . 10
3
4.6 Burner start-up cycle . . . . . . . . . . . . . . . . 10
3
5.
MAINTENANCE . . . . . . . . . . . . . . . . . . . 11
4
4
6.
FAULTS / SOLUTIONS . . . . . . . . . . . . . 12
4
5
5
7
5
4
3
2
1
12
Screw and nuts for flange to be fixed to the heat generator. . No. 4
Flexible oil pipes with nipples . . . . . . . . . . . . . . . . . . . . No. 2
4 pin plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
1
GB
Fig. 1
S7111
13
11
8
8
8
9
9
6
7
8
9
10
Capítulos
Tabla de contenido
